Kichler 43347 User Manual
Kichler Lighting

27) Make wire connections (connectors not provided.) Reference chart below for
correct connections and wire accordingly.
28) Push fixture to ceiling, carefully passing mounting screws through holes in
canopy.
29) Thread knurl knobs onto mounting screws. Tighten knurl knobs to secure
fixture to ceiling.
CABLE LENGTH ADJUSTMENT INSTRUCTIONS
1) Adjust the length of the cables to achieve the desired height of the mounted
fixture. (See cable adjustment detail)
To raise fixture: Push cable up into canopy. Release cable and cable will lock
into place.
To lower fixture: Push button in on cable adjuster and pull cable down.
Release button to lock cable in place.
NOTE: With button pushed in cable will raise and lower. Without button
pushed in cable will only raise up and lock in place.
1) Lower bar with socket cluster down through top of outer shade.
2) Place outer shade with bar over inner shade.
3) Align holes at each end of bar with holes in each bracket on inside of inner
shade.
4) Thread screws down through each hole in bar and into holes in brackets.
Tighten screws to secure inner shade in place.
5) Insert recommended bulbs.
6) Screw threaded pipe into hole in bottom of socket cluster.
7) Thread one hexnut onto end of threaded pipe.
8) Slip one flat washer then one rubber washer over end of threaded pipe.
9) Raise diffuser up to fixture. Pass hole in diffuser over end of threaded pipe.
10) Slip one rubber washer then one flat washer over end of threaded pipe. Thread
hexnut onto end of threaded pipe
11) Thread finial onto end of threaded pipe. Tighten finial to secure diffuser in
place. (DO NOT over tighten.)
12) Determine the amount of stems necessary to achieve desired height of
fixture.
CAUTION: At least one 6" stem must be used.
13) Pass fixture wire from coupling on bar through stem and screw stem to
coupling on top of bar. NOTE: Thread locking compound must be applied to
all stem threads as noted with symbol (3) to prevent accidental rotation of
fixture during cleaning, relamping, etc.
14) Pass fixture wire through remaining stems and screw remaining stems
together.
15) After desired number of stems are assembled to fixture, shorten the cables
just until taut. Refer to Cable Length Adjustment Instructions below.
NOTE: Fixture may be hung with or without loops and chain link.
With loops and chain link:
16) Thread one small threaded pipe into end of each small loop.
17) Pass fixture wire from last stem up through threaded pipe in end of one small
loop. Thread that small loop onto the end of stem.
18) Attach chain link to small loop at end of last stem.
19) Attach second small loop to end of chain link.
20) Pass fixture wire through hole in second small loop.
21) Pass fixture wire from second small loop through hole in canopy. Lower
canopy down over stem. Pass hole in canopy over threaded pipe at end of
second small loop.
22) Pass fixture wire through hole in lockwasher. Thread lockwasher onto threaded
pipe protruding from inside of canopy. Pass fixture wire through hole in
hexnut. Thread hexnut onto threaded pipe.
FOLLOW STEPS 23-29 TO COMPLETE INSTALLATION.
Without loops and chain link:
16) Pass fixture wire from end of last stem through one small threaded pipe.
Thread small threaded pipe into end of last stem.
17) Pass fixture wire through hole in canopy. Lower canopy down and pass
hole in canopy over end of threaded pipe on stem.
18) Pass fixture wire through hole in lockwasher. Thread lockwasher onto threaded
pipe protruding from inside of canopy. Pass fixture wire through hole in
hexnut. Thread hexnut onto threaded pipe.
FOLLOW STEPS 23-29 TO COMPLETE INSTALLATION.
23) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work without shutting off
the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your home. Place the main
power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker switch(s), that
control the power to the fixture or room that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture to be replaced
has a switch or pull chain, place those in the “OFF” position.
24) Find the appropriate threaded holes on mounting strap. Assemble mounting
screws into threaded holes.
25) Attach mounting strap to outlet box. (Screws provided). Mounting strap can be
adjusted to suit position of fixture.
26) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a hole and two raised
dimples. Wrap ground wire from outlet box around green ground screw,
and thread into hole.
B) On fixtures where a cupped washer is provided. Attach ground wire from
outlet box under cupped washer and green ground screw, and thread into
mounting
strap.
If fixture is provided with ground wire. Connect fixture ground wire to outlet
box ground wire with wire connector. (Not provided.) After following the above
steps. Never connect ground wire to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black
White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 8/1/14
IS-43347-US
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST
PRESSED
CABLE ADJUSMENT DETAIL
EL DETALLE DE AJUSTE DEL CABLE
NOT
PRESSED
UP & DOWN
UP ONLY
MOUNTING STRAP
ABRAZADERA DE MONTAJE
CANOPY
ESCUDETE
KNURL KNOB
PERILLA ESTRADA
THREADED
PIPE
TUBO
ROSCADO
FINIAL
CAPUCHON
RUBBER WASHER
ARANDELA DE
CAUCHO
FLAT WASHER
ARANDELA PLANA
DIFFUSER
DIFUSOR
OUTER SHADE
PANTALLA EXTERNA
CABLE
CABLE
LOCKWASHER
ARANDELA DE SEGURIDAD
HEXNUT
TUERCA HEXAGONAL
STEM
VÁSTAGO
3
3
3
BAR
BARRA
SCREW
TORNILLO
INNER SHADE
PANTALLA INTERNA
HEXNUT
TUERCA
HEXAGONAL
LOOP
ANILLO
BRACKET
SOPORTE
HEXNUT
TUERCA HEXAGONAL
RUBBER WASHER
ARANDELA DE
CAUCHO
CHAIN LINK
ESLABÓN DE CADENA
SOCKET CLUSTER
GRUPO DE
PORTALÁMPARAS
FLAT WASHER
ARANDELA PLANA