beautypg.com

Kichler 43121 User Manual

Kichler Lighting

background image

1) Screw long threaded pipe into coupling on top of fixture body.
2) Pass hole in bottom of top column down over top of long

threaded pipe.

3) Lower top trim down over top of long threaded pipe. Set top

trim on top of center column.

4) Slip small washer then lockwasher over end of threaded

pipe. Thread hexnut onto end of threaded pipe.

5) Screw top hook onto end of threaded pipe.
6) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work

without shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your home.

Place the main power switch in the “OFF” position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

switch(s), that control the power to the fixture or room

that you are working on.

c) Place the wall switch in the “OFF” position. If the fixture

to be replaced has a switch or pull chain, place those in

the “OFF” position.

7) Take threaded pipe from parts bag and screw in screw collar

loop a minimum of 6 mm (1/4”). Lock into place with hexnut.

8) Run another hexnut down threaded pipe almost touching

first hexnut. Now screw threaded pipe into mounting strap.

Mounting strap must be positioned with extruded thread

faced into outlet box. Threaded pipe must protrude out the

back of mounting strap. Screw third hexnut onto end of

threaded pipe protruding from back of mounting strap.

9) Connect mounting strap to outlet box.
10) Unscrew the threaded ring from screw collar loop. Take canopy

and pass over screw collar loop. Approximately one half of

the screw collar loop exterior threads should be exposed.

Adjust screw collar loop by turning assembly up or down in

mounting strap. Remove canopy.

11) After desired position is found, tighten both top and bottom

hexnuts up against the bottom and top of the mounting strap.

12) Slip canopy over screw collar loop and thread on threaded

ring. Attach chain (with fixture connected) to bottom of

screw collar loop. Unscrew threaded ring, let canopy and

threaded ring slip down.

13) Weave electrical wire and ground wire through chain links no

more than 3 inches apart. Pass wire through threaded ring,

canopy, screw collar loop, threaded pipe and into outlet box.

14) Grounding instructions: (See Illus. A or B).

A) On fixtures where mounting strap is provided with a

hole and two raised dimples. Wrap ground wire from

outlet box around green ground screw, and thread into hole.

B) On fixtures where a cupped washer is provided. Attach

ground wire from outlet box under cupped washer and

green ground screw, and thread into mounting strap.

If fixture is provided with ground wire. Connect fixture

ground wire to outlet box ground wire with wire connector

(not provided.) after following the above steps. Never connect

ground wire to black or white power supply wires.

15) Make wire connections (connectors not provided). Reference

chart below for correct connections and wire accordingly.

16) Raise canopy to ceiling.
17) Secure canopy in place by tightening threaded ring onto

screw collar loop.

18) Attach crystals as illustrated.

CRYSTAL A

CRYSTAL C

CRYSTAL C

CRYSTAL K

CRYSTAL F

CRYSTAL F

CRYSTAL F

CRYSTAL F

MOUNTING STRAP

ABRAZADERA DE MONTAJE

HEXNUT

TUERCA

HEXAGONAL

THREADED PIPE

TUBO ROSCADO

SCREW COLLAR LOOP

OJAL DE COLLAR

ROSCADO

CANOPY

ESCUDETE

THREADED RING

ANILLO ROSCADO

Date Issued: 8/31/12

IS-43121-US

GREEN GROUND

SCREW

CUPPED

WASHER

A

B

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

(NOT PROVIDED)

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black

White

*Parallel cord (round & smooth)

*Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)

Neutral Wire

CRYSTAL A (6 pcs)

CRYSTAL C (30 pcs)

CRYSTAL F (19 pcs)

CRYSTAL K (1 pc)

CRYSTALS

CRISTALES

SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.

HOOK

CROCHET

TOP TRIM

GUARNICIÓN SUPERIOR

LONG THREADED PIPE

TUBO ROSCADO LARGO

TOP COLUMN

COLUMNA SUPERIOR

LOCKWASHER

ARANDELA DE

SEGURIDAD

SMALL WASHER

ARANDELA PEQUEÑA

HEXNUT

TUERCA HEXAGONAL