beautypg.com

Kichler 15314 User Manual

Kichler Lighting

background image

SAFETY INSTRUCTIONS

READ THIS FIRST

KEEP THESE INSTRUCTIONS

This fixture is intended for installation in accordance with the National

Electric Code (NEC) and Local code specifications. Failure to adhere to

these codes and instructions may result in serious injury and/or property

damage and will void the warranty.

1) WARNING: This fixture is not to be installed within 10 feet (3M) of a pool,

spa or fountain.

2) This fixture is to be used only with a power unit (transformer) rated a

maximum of 300 W (25 AMPS) 15 volts.

3) The #18 ga. fixture wire is not intended for direct burial.

4) Direct burial rated wire is to be buried a minimum of 6” (152mm) beneath

the surface of the ground.

NOTE: If additional Direct Burial wire is needed, contact your local

Kichler

®

landscape distributor.

• 8 GA wire can be purchased in length of 250’ (76 M), 15503-BK.

• 10 GA wire can be purchased in length of 250’ (76 M), 15504-BK.

• 12 GA wire can be purchased in lengths of 100’ (30 M), 15501-BK; 250’

(76 M), 15502-BK; 500’ (152M), 15505-BK; and 1000’ (304 M), 15506-BK.

5) Fixture shall not use a tungsten halogen lamp unless the fixture is marked

for use with such lamps.

6) Wiring connections must be made with approved/listed wire connection

device(s) suitable for the application. Do not exceed manufacturers’ wiring

combination specifications for size and quantity of conductors.

ASSEMBLY AND INSTALLATION

1) Determine desired location for mounting fixture.

2) At desired location, hammer stake (A) into ground. To avoid damage to

stake, place a board on top of stake while hammering. If ground is hard

and stake is difficult to install, make a crosscut in ground using a flat shovel.

3) Clear away area in ground at wireway slot (B) in top of stake (A).

4) Lay 12V cable into wireway slot (B) and screw stem (C) into stake (A). If

assembly does not look straight, adjust by pushing or pulling on stake only.

5) Install provided lamp (E) to socket inside fixture body (D).

6) Slip threaded studs (J) assembled to bottom of fixture hood (F) through

holes in arms (G) on top of fixture body.

7) Secure in place with ball knobs (H).

8) TURN OFF POWER.

9) Make wire connections using supplied Quic Disc

following instructions

below, or using other approved wiring connection method (not supplied.)

For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page

Para informacion de la garantia por favor visite: www.landscapelighting.com/portal/warranty_page

Date Issued: 12/2/11

IS-15314-US

A

J

F

C

G

H

D

E

QUIC DISC

WIRING INSTRUCTIONS

Turn off power.

The full length of the 18 GA fixture wire may be used to connect with the 10 GA or 12 GA cable provided the following conditions are met:

• Wiring is to be protected by routing close to the fixture or accessory or secured to a building structure such as house or deck.

• 18 GA fixture wiring is to be cut off so that it is attached to the connector within 6 inches of the fixture or building structure.

• If it is necessary to make the connections underground, then no more than 6 inches of the 18 GA fixture wire is to be buried.

The Quic Disc

connector is designed to install one fixture and accommodates one 18 GA fixture wire and one 10 GA or one 12 GA supply wire.

Place the 10 gauge supply wire across the area marked 10 GA on Quic Disc

or place the 12 gauge supply wire across the area marked 12 GA

on Quic Disc

.

Place the 18 gauge fixture wire across the area marked 18 GA on the Quic Disc

. After the wires are in place, connect the top of the Quic Disc

to the base with supplied screw, making sure that the wires remain flat in the bottom portion of the Quic Disc

, and the screw is tightened all the

way down.

The copper contacts will automatically pierce the wires’ insulation. Excess 18 GA fixture wire that sticks out the end of the Quic Disc

is to be cut off.

Make no other wiring connections to the 18 GA fixture wire.

B

This manual is related to the following products: