Features and controls, Instrument cluster – Polaris 2015 Ranger Diesel / Crew Diesel User Manual
Page 36

34
FEATURES AND CONTROLS
Instrument Cluster
Information Display Area
Programmable Service Interval
The initial factory service interval setting is 50 hours. Each
time the engine is started, the engine hours are subtracted
from the service interval hours. When the service interval
reaches 0, the LCD wrench icon will flash for approximately
10 seconds each time the engine is started.
To change the hour setting or reset the function, follow these
steps:
1. Toggle the MODE button until the wrench icon is displayed in the information area.
2. Press and hold the MODE button until the information display area begins to flash.
3. Toggle the MODE button to increase the service interval hours in 5 hour increments to a
maximum of 100 hours.
4. To turn off the service interval function, toggle the MODE
button until “OFF” is displayed
.
Check Engine / Trouble Code Display
The diagnostic mode is accessible only when the check
engine MIL has been activated.
Use the following procedure to display diagnostic trouble
codes that were activated during current ignition cycle
causing the MIL to illuminate. Diagnostic trouble codes will
remain stored in the gauge (even if MIL turns off) until the
key is turned off.
1. If the trouble codes are not displayed, use the MODE button to toggle until “CK ENG”
displays on the information display area.
2. Press and hold the MODE button to enter the diagnostics code menu.
3. A set of three numbers will appear in the information area.
4. The first number (located far left) can range from 0 to 9. This number represents the total
number of trouble codes present (example: 2 means there are 3 codes present).
5. The second number (located top right) can be 2 to 6 digits in length. This number
equates to the suspected area of fault (SPN).
6. The third number (located bottom right) can be 1 to 2
digits in length. This number equates to the fault mode
(FMI).
7. See your dealer for Diagnostic Trouble Codes.
8. If more than one code exists, press the MODE button to
advance to the next trouble code.
To exit the diagnostic mode, press and hold the MODE button
or turn the ignition key OFF once the codes are recorded.
- 2014 Ranger XP 900 2014 Ranger Crew 900 2013 Ranger XP 900 2013 Ranger 800 2013 Ranger 6x6 800 2013 Ranger Crew 800 2011 Ranger Diesel 2010 Ranger 4x4 2010 Ranger EV 2011 Ranger EV 2011 Polaris EV 2011 Polaris LSV 2011 Ranger 4x4 500 EFI 2011 Ranger Crew 500 EFI 2011 Ranger 400 2010 Ranger 400 HO 2010 Ranger XP 2010 Ranger HD 2010 Ranger 6x6 2010 Ranger Crew 2012 Ranger Diesel 2014 Ranger Diesel 2014 Ranger Crew Diesel 2011 Ranger XP 800 2011 Ranger 800 HD 2011 Ranger 800 6x6 2011 Ranger 800 Crew 2013 Ranger Diesel 2013 Ranger 500 Midsize 2013 Ranger Crew 500 2012 Ranger XP 800 2012 Ranger 800 HD 2012 Ranger 800 6x6 2012 Ranger 800 Crew 2015 Ranger XP 900 2015 Ranger Crew 900 2016 Ranger XP 570 2016 Ranger XP 570 EPS 2016 Ranger Crew 570 2016 Ranger Diesel 2016 Ranger Crew Diesel 2015 Ranger Crew 570 Full Size 2015 Ranger 570 Full Size 2016 Ranger XP 900 2016 Ranger Crew 900 2016 Ranger XP 900 High Lifter