RLE TH140D - Manual (Page 2)

VERIS INDUSTRIES
™
inStallation GUiDe HWl SerieS
Z202637-0Y PAGE 2 ©2010 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 09101
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
1. Remove the cover by pressing the tab at the top of the sensor while pulling
outward from the top of the cover.
3. Punch out openings in the backplate.
installation
2. Remove the backplate by unfastening the sensor from the bottom of the backplate
and pivoting the sensor outward.
correct incorrect
4. Position the sensor vertically on the wall, 4 1/2 feet above the floor.
ProDuct iDentification
* In order for unit to display both temp and RH, use the
TA or D temp selection.
Temp displayed on LCD is read from temperature
transmitter, not resistive element.
NIST US or EU Temp. Sensor Type Display Accuracy
S = Standard
C = CE A = Transmitter: 10° - 35°C (50°
- 95°F and 0° - 50°C (32° - 122°F)
(switchable)
B = 100R Platinum, RTD
C = 1k Platinum, RTD
D = 10k T2, Thermistor
E = 2.2k, Thermistor
F = 3k, Thermistor
G = 10k CPC, Thermistor
H = 10k T3, Thermistor
J = 10k Dale, Thermistor
K = 10k with 11k shunt, Thermistor
M = 20k NTC, Thermistor
N = 1800 ohm TAC, Thermistor
Q = 1uA/C, Linitemp
R = 10k US, Thermistor
S = 10k 3A 221
T = 100k, Thermistor
U = 20k “D”, Thermistor 1 = 1%
2 = 2%
3 = 3%
5 = 5% = No
HW Temp Cal Cert Option Value
A = 1k
F = 10k
G = 20k
K = 50k
M =100k
Options Available
X = No Cert
1 = 1pt Cal
2 = 2pt Cal 1 = Push Button Override
2 = Set Point Slider
3 = Push Button Override
and Set Point Slider
T = Temp*
X = No Temp
(Stop here) N = NIST
(1% and 2% only)
X = No
(2%, 3%, and 5% only)
X
NIST US or EU Temp. Sensor Type Display Accuracy
S = Standard
C = CE None = Select for TA temp option only
B = 100R Platinum, RTD
C = 1k Platinum, RTD
D = 10k T2, Thermistor
E = 2.2k, Thermistor
F = 3k, Thermistor
G = 10k CPC, Thermistor
H = 10k T3, Thermistor
J = 10k Dale, Thermistor
K = 10k with 11k shunt, Thermistor
M = 20k NTC, Thermistor
N = 1800 ohm TAC, Thermistor
Q = 1uA/C, Linitemp
R = 10k US, Thermistor
S = 10k 3A 221
T = 100k, Thermistor
U = 20k “D”, Thermistor 1 = 1%
2 = 2%
3 = 3%
5 = 5% = LCD
HW
N = NIST
(1% and 2% only)
X = No
(2%, 3%, and 5% only) T = Temp*
TA = Transmitter
only
D = Transmitter
and resistive
element
X = No Temp
(Stop here)
L Temp Cal Cert Option Value
A = 1k
F = 10k
G = 20k
K = 50k
M =100k
Options Available
X = No Cert
1 = 1pt Cal
2 = 2pt Cal 1 = Push Button Override
2 = Set Point Slider
3 = Push Button Override
and Set Point Slider