REMKO RKS 435 H - Manual (Page 12)

Condensation connection
Be�au��e the temperature on the
regi��ter i�� below the dew point,
�onden��ation i�� formed during
heating.�
The lower hou��ing �over on the
outdoor unit take�� the form of a
�olle�tor.� The �onden��ation �on-
The �onden��ation �on- The �onden��ation �on-
ne�tion ��upplied i�� to be fitted
here.�
■�
The on-��ite �onden��ation pipe
mu��t be laid with a gradient of
at lea��t 2%.�
�f ne�e����ary, fit in��ulation that i��
re��i��tant to vapour diffu��ion.�
■�
When operating the unit at an
external temperature of le����
than 0°C, the �onden��ation
pipe mu��t be laid with fro��t
prote�tion.� The �u��tomer mu��t
The �u��tomer mu��t The �u��tomer mu��t
keep the lower hou��ing �over
free of fro��t to guarantee �on-
��tant drainage of the �onden��a-
tion.� �f ne�e����ary, auxiliary pipe
heating ��hould be fitted.�
■�
After laying the pipe��, free
drainage of the �onden��ation
mu��t be te��ted and permanent
impermeability en��ured.�
Electrical connection
The �onne�tion�� on the outdoor
unit are lo�ated in��ide the unit
above the �onne�ting valve��.�
The �ondu�tor �ro����-��e�tion of
the power ��upply depend�� on the
��tru�tural �ondition�� and the �on-
ne�ted load of the unit.�
Connecting the outdoor unit
Before ��tarting the �onne�tion,
ob��erve the following in��tru�tion��:
Connecting the RXW 0
wall unit
A power ��upply to the indoor unit
and a 5-wire �ontrol line from the
outdoor unit to the indoor unit
mu��t be in��talled.�
Connecting the RXW 80
wall unit
A power ��upply to the indoor unit
and a 6-wire �ontrol line from the
outdoor unit to the indoor unit
mu��t be in��talled.�
■�
The power ��upply �ome�� from
the �onne�ting terminal�� on the
RXW indoor unit.�
We re�ommend u��ing a ma��ter
��wit�h and a repair ��wit�h.�
■�
�f the line�� are in��talled in area��
with ��trong magneti� field��, the
�ontrol line�� ��hould be ��hielded.�
■�
The outdoor unit i�� a�tuated
by the �onne�ting line from the
indoor unit.�
■�
The ��y��tem i�� fu��ed a�� ��et out
in the te�hni�al data.�
Connecting the RXD
ceiling cassette
A power ��upply to the outdoor
unit and a 6-wire �ontrol line from
the outdoor unit to the indoor unit
mu��t be in��talled.�
■�
The �u��tomer mu��t in��tall the
�onne�ting box �lo��e to the
outdoor unit.�
We re�ommend u��ing a ma��ter
��wit�h and a repair ��wit�h.�
■�
�f the line�� are in��talled in area��
with ��trong magneti� field��, the
�ontrol line�� ��hould be ��hielded.�
■�
The power ��upply to the indoor
unit �ome�� from the �onne�ting
line from the outdoor unit.�
■�
The ��y��tem i�� fu��ed a�� ��et out in
the te�hni�al data.�
The pro�edure for �onne�ting the
line i�� a�� follow��:
1.� Remove the unit �over.� Remove the unit �over.�
2.� Remove the ��ide panel�� on the Remove the ��ide panel�� on the
�onne�tion.�
3.� Sele�t the �ro����-��e�tion of the Sele�t the �ro����-��e�tion of the
�onne�ting line ba��ed on the
��pe�ifi�ation��.�
4.� Run the two line�� through the Run the two line�� through the
edge prote�tion ring�� on the
fixed �onne�ting plate.�
5.� Conne�t the line�� a�� ��hown in Conne�t the line�� a�� ��hown in
the �onne�tion diagram.�
6.� Se�ure the line in the ��train Se�ure the line in the ��train
relief and re-a����emble the unit.�
REMKO RKS
12