beautypg.com

Protech audio, Installation, Alignment – Protech Audio 571B User Manual

Page 2: Specifications - model 571b

background image

INTEGRA III SYSTEM

CONNECTOR & PROGRAM DRAWING

MODEL 571B

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

K1 ARM A

K1 ARM B

GROUND

K1 N/C A

K1 N/C B

K1 N/O A

K1 N/O B

GROUND

K2 ARM A

K2 ARM B

K2 N/C A

K2 N/C B

GROUND

K2 N/O A

K2 N/O B

K3 ARM A

K3 ARM B

K3 ARM C

K4 ARM D

K3 N/C A

K3 N/C B

K3 N/C C

K3 N/C D

K3 N/O A

K3 N/O B

K3 N/O C

K3 N/O D

GROUND RELAY CONTROL PINS TO ACTIVATE RELAYS

INSTALLATION

The 571B Relay Switching Card is designed to be
mounted in the Model 857B, or 858B Card Frame
Assembly.
The Model 857B Card Frame will accomodate up to 10
audio cards, and requires an external power supply (Model
66708).
The Model 858B Card Frame will accomodate up to
9 audio cards, and has a built-in power supply card
(Models 2000-PS-A).

Both card frames assemblies bus the DC power to the
individual card slots, and provide screw-type barrier termi-
nation points for audio and DC connections.

The determination as to which backplane assembly to use
in your project, was made prior to our factory receiving the
order. The backplane assembly you have received will
accomodate the group of cards you or your designer have
speciifed.

4- Unpack each individual card, inspect for shipping
damage, and assuming none is found, slide the
card
half-way into the appropriate slot. After all cards have
been installed half-way into the card frame, plug in one
card at a time and turn on the power supply. Make sure no
unusual loading is noticed at the power supply. If loading
is noticed, turn off the power supply, unplug the card and
recheck terminations. If no loading is noticed, continue
inserting each card in the card frame, checking power
supply loading as each card is plugged in. When all the
cards have been plugged in, the installation is complete,
and all that remains is the alignment.

Page 2

The actual steps necessary for installation of the 571B
Relay card, are comparable to those necessary for any
of the INTEGRA III SYSTEM cards. They are as follows:

1- Mount the card frame in an appropriate EIA 19" width
rack, using 4 screws of sufficient tensile strength to
provide secure mounting.

2- A determination has been made as to which type of
power supply will be used on your system. Follow the
instructions for the type of power supply you will be
installing.

EXTERNAL POWER SUPPLY. If an external power
supply is to be used, terminate the proper supply
connections to pins 1, 2, & 3 of the DC connector,
as shown in the card frame layout drawing Turn on the
power supply, and using a DC voltmeter, check for
correct voltage and polarity at pins 1, 2, & 3 of of the DC
connector.

INTERNAL POWER SUPPLY. If a plug-in power supply
card is to be used, plug in the supply card, and check for
proper illumination of both plus and minus DC green
LED's.

3- Terminate all input, output, and switch connections,
using the card connection drawing on the facing page.
Shielded cable is recommended for all audio connections.

Note 1-
The alignment procedures for INTEGRA III SYSTEM
cards, differ from card type to card type. Therefore it is
necessary to consult the alignment procedure for each
type of card being installed, to properly align a card frame
using different card types.

The Model 571B does not require alignment.
Operation of the card may be checked in the following
manner:

1- Apply a signal representative of the actual signal level
to
be used, to the relay.

2- While monitoring the output, ground the appropriate
control pin, and check for proper signal continuity at the
output pin.

3- Repeat steps 1 & 2 for each switch channel on the
Model 571B.

This completes the installation and alignment of your
Model 571B Relay Switching Card. The card(s) may be
expected to deliver years of uninterrupted service.

ALIGNMENT

857B & 858B BACKPLANE CONNECTIONS

PROTECH AUDIO

®

K1 CONTROL

K2 CONTROL

K3 CONTROL

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

Number of Relays....................
Contact

Arrange-

ment...............
On

Resis-

tance...........................
Contact

Rat-

ings........................

O p e r a t i n g
Time.........................
R

e

l

e

a

s

e

Time...........................
Power

Require-

ments................
Size...........................................

Specifications - Model 571B

2 Double-Pole, 1 Four-Pole
Form C
0.2 Ohm
0.3 Amp 125 VAC
0.3 Amp 110 VDC
1.0 Amp 30 VDC
5.0ms
2ms
+15-24VDC @ 60ma Per
Module
2.5"H x 8.0"D x 1.1"W