Denon AVR-1611 - Manual (Page 48)

45
ENGLISH
Basic version
Simple version
Information
Advanced version
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu
Audio Adjust
Setting items Setting details
S.Back
Sets the method of
generating of the surround
back channel. n For 2-channel sources
ON : The surround back channel is used.
OFF : No signal is played from the surround back channels.
n For Multi-channel sources
Set the decoding method for the surround back channel.
DSCRT ON : Play the surround back signals included in the 7.1-channel
source.
MTRX ON : Generate and play the surround back signals from the
surround channel signals.
ES MTRX
z 1 : Generate and play the surround back signals from the
surround channel signals of the DTS source.
ES DSCRT
z 2 : Play the surround back signals included in the
6.1-channel DTS source.
PLgx CINEMA
z 3 : Generate and play the surround back signals by
decoding the signals in the Dolby Pro Logic gx Cinema mode.
PLgx MUSIC : Generate and play the surround back signals by
decoding the signals in the Dolby Pro Logic gx Music mode.
OFF : Do not play the surround back channel.
z 1 This can be selected when playing DTS sources.
z 2 This can be selected when playing DTS sources including a signal to
identify discrete 6.1-channel signals.
z 3 This can be selected when “Speaker Config.” – “S.Back” (vpage 49)
is set to “2sp”.
• This can also be set by pressing STANDARD .
• If the source being played contains a surround
back signal, the decoder type is automatically
selected by the AFDM function. Set “AFDM” to
“OFF” to switch to your preferred decoder.
NOTE
If the setting in “Speaker Config.” – “S.Back” (vpage 49) is “None”,
“S.Back” is not displayed.
Front Height
Determine whether to use
front height channel. ON : Audio is output from the front height speaker.
OFF : Audio is not output from the front height speaker.
NOTE
• “Front Height” is displayed with the settings listed below.
• When “Amp Assign” (vpage 49) is set to “Front Height”.
• When the “Speaker Config.” – “Front Height” setting (vpage 49) is
set to other than “None”.
• “Front Height” cannot be set if the HD Audio source being played
includes a front height channel. In this case, the Front height channel
is played back without decoding in PLgz mode, using the input signal.
Setting items Setting details
Height Gain
Control the front height
channel volume. Low : Reduce the front height channel volume.
Mid : Front height channel sound is output with standard sound volume.
High : Increase the front height channel volume.
NOTE
“Height Gain” is displayed for the following settings.
• When “Amp Assign” (vpage 49) is set to “Front Height”.
• When the “Speaker Config.” – “Front Height” setting (vpage 49) is set
to other than “None”.
• When surround mode is “PLgz” or the PLgz decoder is used.
Subwoofer
Turn subwoofer output on
and off. ON : The subwoofer is used.
OFF : The subwoofer is not used.
NOTE
This can be set when the surround mode is “DIRECT” (vpage 65, 66), and
the “Subwoofer Mode” (vpage 50) is “LFE+Main”.
Default
The “Surround Parameter”
settings are returned to the
default settings. Yes : Reset to the defaults.
No : Do not reset to the defaults.
Tone
Default settings are underlined.
Adjust the tonal quality of the sound.
Setting items Setting details
Tone Control
Set the tone control function
to ON and OFF. ON : Allow tone adjustment (bass, treble).
OFF : Playback without tone adjustment.
“Tone Control” can be set when “Dynamic EQ” (vpage 46) is set to
“OFF”.
NOTE
• “Tone Control” settings are not reflected to ZONE2.
• The tone cannot be adjusted in the direct mode.
Bass
Adjust low frequency range
(bass). –6dB – +6dB (0dB)
“Bass” can be set when “Tone Control” is set to “ON”.
Treble
Adjust high frequency range
(treble). –6dB – +6dB (0dB)
“Treble” can be set when “Tone Control” is set to “ON”.