Denon AVR-2802 - Manual (Page 28)

28
ENGLISH
SELECT
(Main unit)
1 Turn the SELECT knob to select the surround
mode.
VOLUME LEVEL
AUTO
LOCK
STAND BY DIGITAL PCM
SIGNAL DIGITAL INPUT
REMOTE
SENSOR
B
2 1 1,3
2 Press the SURROUND PARAMETER button.
Press and hold in the surround parameter button to select the parameter you want to
set.
• The parameters which can be set differ for the different surround modes. (Refer to
“Surround Modes and Parameters” on page 29.
SURROUND
PARAMETER
(Main unit)
3 Display the parameter you want to adjust, then turn the SELECT knob to set it.
NOTES:
• When playing PCM digital signals or analog signals in the DOLBY PRO LOGIC, DTS NEO:6 modes and the
input signal switches to a digital signal encoded in Dolby Digital, the Dolby surround mode switches
automatically. When the input signal switches to a DTS signal, the mode automatically switches to DTS
surround.
• When the “5CH/6CH STEREO” mode is selected, the display differs according to the SB CH OUT setting.
Surround Back CH ON : 6CH STEREO
Surround Back CH OFF : 5CH STEREO
• Operating the surround mode and surround parameters from the main unit‘s panel.
• When turned clockwise
• When turned counterclockwise
DIRECT STEREO DOLBY PRO LOGIC II DTS NEO:6 5/6CH STEREO
MONO MOVIE ROCK ARENA JAZZ CLUB VIDEO GAME MATRIX
DIRECT STEREO DOLBY PRO LOGIC II DTS NEO:6 5/6CH STEREO
MONO MOVIE ROCK ARENA JAZZ CLUB VIDEO GAME MATRIX
To select the surround mode while adjusting the surround parameters, channel volume or tone control,
press the surround mode button then operate the selector.
SURROUND
MODE
(Main unit)
Tone control setting
• Use the tone control setting to adjust the bass and treble as desired.
• To operate the tone control from the remote control unit.
1 Display the surround parameter
screen on the monitor.
The screen for the selected
surround mode appears.
“TONE” cannot be selected
in the Direct mode. MENU/GUIDE
SURROUND PARAMETER
DVD
START LEARNED/TX
SPEAKER
TUNING
BAND TITLE MENU/GUIDE
MODE
MEMORY
RDS
PTY
RT
USE/LEARN T.TONE MULTI DVD SET UP
RETURN
STATUS
DISPLAY
ON SCREEN
DOLBY / DTS
SURROUND DIRECT
DSP SIMULATION 5CH / 6CH STEREO STEREO
INPUT MODE ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS PHONO
VCR-1 CD CDR / TAPE CHANNEL
VCR-2/V.AUX TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD MULTI CDR/MD TAPE
SYSTEM SETUP SURROUND
PARAMETER
CH SELECT
SELECT
RC-904
1 2 3
4
SET
A / B
CALL OFF
ENTER
ON / SOURCE
5 6
7 8 9
+10 0
2,4
1,6
3,5
(Remote control unit)
2 Select “TONE”.
(Remote control unit)
3 Switch to the Tone Control
screen.
ENTER
(Remote control unit)
4
5 Enter the setting.
The surround menu screen re-appears.
ENTER
(Remote control unit)
6 To end the setting mode, press the surround parameter button again.
MENU/GUIDE
SURROUND PARAMETER
(Remote control unit)
(Remote control unit)
To select Bass or Treble.
(Remote control unit)
To set the level.
1 The tone switches as follows each time the TONE CONTROL button is pressed.
• To operate the tone control from the main unit.
TONE
CONTROL
(Main unit)
1 TREBLE 0 BASS
2 With the name of the volume to be adjusted selected, turn the SELECT knob to adjust
the level.
• To increase the bass or treble:
Turn the control clockwise. (The bass or treble sound can be increased to up to +12 dB in
steps of 2 dB.)
• To decrease the bass or treble:
Turn the control clockwise. (The bass or treble sound can be decreased up to –12 dB in
steps of 2 dB.)
SELECT
(Main unit)