Artesyn MVME55006E Single Board Computer Installation and Use (July 2014) User Manual
Artesyn Equipment
Table of contents
Document Outline
- MVME55006E Single Board Computer
- Contents
- About this Manual
- Hardware Preparation and Installation
- 1.1 Overview
- 1.2 Introduction
- 1.3 Declaration of Conformity
- 1.4 Getting Started
- 1.5 Overview of Startup Procedures
- 1.6 Unpacking Guidelines
- 1.7 Configuring the Hardware
- 1.7.1 Configuring the Board
- 1.7.2 Ethernet 2, PMC/SBC Mode, and P2 I/O Selection Headers (J6, J7, J28, J32, J34, J97 – J110)
- 1.7.3 Flash Boot Bank Select Header (J8)
- 1.7.4 Flash 0 Programming Enable Switch (S3-1)
- 1.7.5 Safe Start ENV Switch (S5-1)
- 1.7.6 Flash 0 Block Write Protect Switch (S3-2)
- 1.7.7 SROM Initialization Enable Switch (S5-2)
- 1.7.8 PCI Bus 0.0 Speed Switch (S4-1)
- 1.7.9 VME SCON Select Header (J27)
- 1.7.10 PCI Bus 1.0 Speed Switch (S4-2)
- 1.7.11 EEPROM Write Protect Switch (S3-3)
- 1.7.12 Setting the PMC Vio Keying Pin
- 1.8 Installing the RAM5500 Module
- 1.9 Installing PMCs
- 1.10 Installing the Board
- 1.11 Startup and Operation
- 1.12 Applying Power
- 1.13 Switches and Indicators
- Functional Description
- 2.1 Overview
- 2.2 Block Diagram
- 2.3 Features
- 2.4 Processor
- 2.5 L3 Cache
- 2.6 System Controller
- 2.7 Flash Memory
- 2.8 System Memory
- 2.9 PCI Local Buses and Devices
- 2.10 Asynchronous Serial Ports
- 2.11 Real Time Clock and NVRAM
- 2.12 System Control and Status Registers
- 2.13 Sources of Reset
- 2.14 VME Interface
- 2.15 PMC Expansion
- 2.16 Debug Support
- RAM55006E Memory Expansion Module
- MOTLoad Firmware
- Connector Pin Assignments
- 5.1 Introduction
- 5.2 Connectors
- 5.2.1 Asynchronous Serial Port Connector (J1)
- 5.2.2 Ethernet Connectors (J2)
- 5.2.3 IPMC Connector (J3)
- 5.2.4 PCI/PMC Expansion Connector (J4)
- 5.2.5 CPU COP Connector (J5)
- 5.2.6 PMC 1 Interface Connectors (J11, J12, J13, J14)
- 5.2.7 Boundary Scan Connector (J18)
- 5.2.8 PMC 2 Interface Connectors (J21, J22, J23, J24)
- 5.2.9 Asynchronous Serial Port (COM2) Planar Connector (J33)
- 5.2.10 VMEbus Connectors (P1 & P2) (PMC Mode)
- 5.2.11 VMEbus Connectors (P1 & P2) (SBC Mode)
- 5.2.12 Memory Expansion Connector (P4)
- 5.3 Headers
- A Specifications
- B Thermal Validation
- C Related Documentation
- Safety Notes
- Sicherheitshinweise