Document Outline

• About This Manual
• 1.0 Introduction
  • 1.1 Unpacking and Inspection
  • 1.2 Repacking
  • 1.3 DC-190 Scale Capacities and Resolutions
  • 1.4 DC-190 Console
    • 1.4.1 Annunciators
    • 1.4.2 DC-190 Keypad
• 2.0 Installation
  • 2.1 Locking and Unlocking
  • 2.2 Setting Up
  • 2.3 Powering Up the DC-190
    • 2.3.1 AC Power Source
    • 2.3.2 DC Battery Pack Replacement/Installation
    • 2.3.3 DC Battery Operation
    • 2.3.4 Battery Charging
  • 2.4 Setting Time and Date
  • 2.5 Installing Cable Strain Relief
  • 2.6 Pole Mounting Instructions
  • 2.7 Load Cell Replacement
    • 2.7.1 Single-Platform Load Cell Replacement
    • 2.7.2 Dual-Platform Load Cell Replacement
• 3.0 Scale Setup
  • 3.1 Scale Configurations
    • 3.1.1 Configuring SPECs 16 and 17
    • 3.1.2 Scale Configurations, No Force Balance Attached
    • 3.1.3 Scale Configurations, Including Force Balance
  • 3.2 Serial Configurations
    • 3.2.1 Configuring SPEC 13
    • 3.2.2 FORCE BALANCE (DIN-8) and 232C/PRINTER (D-Sub) Port Connections
    • 3.2.3 SCANNER Port Connections
• 4.0 Configuration Settings
  • 4.1 Configuration Procedure
  • 4.2 Customer Specification (141 Settings)
  • 4.3 Weight and Measurement Specifications (142 Settings)
  • 4.4 RS-232 Specifications (143 Settings)
• 5.0 Calibration
• 6.0 Scale Operations
  • 6.1 Entering Tare Weights
  • 6.2 Toggle Between Scales
  • 6.3 Toggling Between Net and Gross Weight
  • 6.4 Entering Unit Weights
    • 6.4.1 Unit Weight Operation by Sampling
    • 6.4.2 Unit Weight Operation by Key Entry
    • 6.4.3 Clearing Unit Weight
  • 6.5 Part Accumulation and Reduction–Without Recalling an Item Code
    • 6.5.1 Part Accumulation
    • 6.5.2 Part Reduction
    • 6.5.3 Clearing Accumulated Data
  • 6.6 Other Operations
    • 6.6.1 Set New Vendor Name
    • 6.6.2 Set New Operator Name
    • 6.6.3 Set New Batch Print Quantity
    • 6.6.4 Set New Sequence Number
• 7.0 Scale Programming
  • 7.1 Item Code Storage
  • 7.2 Item Code Maintenance
  • 7.3 Using Item Code in Normal Mode
    • 7.3.1 Inventory Operations Related to the Item Code Quantity Value
  • 7.4 Global Setpoint Programming– Setpoints Not Tied to an Item Code
    • 7.4.1 Procedure
• 8.0 RS-232 Specifications
  • 8.1 RS-232 Ports
  • 8.2 Eltron Printers
  • 8.3 Epson Tape Printers
  • 8.4 Epson Ticket Printers
  • 8.5 Digi BCP-300 Printer
  • 8.6 PC Output Data Formats
    • 8.6.1 PC Output Data Format With Header
    • 8.6.2 PC Output Data Format Without Header
  • 8.7 Data
  • 8.8 Status Data Byte
  • 8.9 Bar Code Scanners
  • 8.10 Header
  • 8.11 Z Commands
• 9.0 PC Connections and Label Formatting
  • 9.1 Using HyperTerminal
    • 9.1.1 HyperTerminal Setup
    • 9.1.2 Using HyperTerminal to Request Data
    • 9.1.3 Saving Data Sent to HyperTerminal
    • 9.1.4 Example of HyperTerminal Data
  • 9.2 Creating Labels for Eltron 2700-Series Printers
    • 9.2.1 Editing Text and Bar Code Fields
    • 9.2.2 Adding and Downloading Label Graphics
    • 9.2.3 Generating the EPL and EJF Files
    • 9.2.4 Editing the EJF File
    • 9.2.5 Downloading the EJF File
    • 9.2.6 Scale Configuration
• 10.0 Appendix
  • 10.1 SPEC Code Worksheets
  • 10.2 Scale Capacity and Display Resolution
  • 10.3 Connector Pinouts
  • 10.4 Cable Wiring
    • 10.4.1 TM-U295/TM-U200 Cables
    • 10.4.2 Eltron 2722/2742 Cables
    • 10.4.3 BCP-300 Cable
  • 10.5 Y-Cable Wiring Diagram
  • 10.6 DC-190 Messages
  • 10.7 Clearing Locked-Up Scale (888888 Error)
  • 10.8 DC-190 Character Code List (Teraoka Code)
  • 10.9 Bar Code Board
  • 10.10 PSC QuickScan 6000 Setup
  • 10.11 DC-190 Ultra Count Specifications
• DC-190 Ultra Count Limited Warranty