Televes T.0X DVBS2-COFDM CI TWIN MUX 3TP(2SAT):2CH - Manual (Page 20)

MUX DVBS2_QAM/COFDM CI Twin
20
unit has been assigned a unique address on the
bus, or the units will not communicate. The valid
address range goes from 1 to 254 (which is the
maximum number of devices controllable from
a single headend controller module).
•
Selection of the output frequency step
There are two options for each of the two
outputs:
» 166 KHz
» 125 KHz
•
Frequency mode/Table of channels
Using this menu, the user can select one of the
two modes available to program the output
frequency.
Choices are: a) By entering the channel
frequency value, and b) by selecting the
channel in one of the following tables:
• CCIR N.Z.Ind • South Africa
• Russia (OIRT) • Italy)
• China Taiwan • Poland
• Ireland
• France
• Chile M/N • Australia
CONFIG ))
Dir CDC: 001
Salto:166KHz
CCIR N.Z.Ind
CONFIG ))
CDC Adr: 001
Step1:166KHz
CCIR N.Z.Ind
CONFIG ))
Dir CDC: 001
Salto:166KHz
Frecuencia
CONFIG ))
CDC Adr: 001
Step2:166KHz
Frequency
CONFIG ))
Dir CDC: 001
Salto:166KHz
CCIR N.Z.Ind
CONFIG ))
CDC Adr: 001
Step1:166KHz
CCIR N.Z.Ind
CONFIG ))
Dir CDC: 001
Salto:166KHz
Frecuencia
CONFIG ))
CDC Adr: 001
Step2:166KHz
Frequency
two modes available to program the output
frequency. Choices are: a) By entering the
channel frequency value, and b) by selecting
the channel in one of the following tables:
• CCIR N.Z.Ind • South Africa
• Russia (OIR
• Italy)
• China Taiwan • Poland
• Ireland
• France
• Chile M/N • Australia
CONFIG ))
Dir CDC: 001
CCIR N.Z.Ind
CONFIG ))
CDC Adr: 001
CCIR N.Z.Ind
CONFIG ))
Dir CDC: 001
Frecuencia
CONFIG ))
CDC Adr: 001
Frequency
CONFIG ))
Dir CDC: 001
CCIR N.Z.Ind
CONFIG ))
CDC Adr: 001
CCIR N.Z.Ind
CONFIG ))
Dir CDC: 001
Frecuencia
CONFIG ))
CDC Adr: 001
Frequency
5.2.a.2 Configuration menu 1 (Ref.
564301)
The first extended menu allows selecting the
following parameters:
•
Dir CDC
Address of the device that allows selecting
it via a control BUS connected to the Headend
Control Module (CDC)
With this menu you can change the address
of the unit on the remote control bus (when
the unit is connected to a headend control
module via its communications BUS). It is the
responsibility of the user to ensure that each
5.2 Extended menu
To access this menu make a long press on key
(more than 3 sec). It displays a number of less
frequently used configuration options, called
extended menus.
Be aware that the same key is used to switch
between “Service menu” (see section 5.1.e) and
“PIDs menu” (seesection5.1.e.1).
5.2.a.1 Configuration menu 1 (Ref.
564401)
The first extended menu allows selecting the
following parameters:
•
Dir CDC
Address of the device that allows
selecting it via a control BUS connected
to the Headend Control Module (CDC).
With this menu you can change the address
of the unit on the remote control bus (when
the unit is connected to a headend control
module via its communications BUS). It is the
responsibility of the user to ensure that each
unit has been assigned a unique address on the
bus, or the units will not communicate. The valid
address range goes from 1 to 254 (which is the
maximum number of devices controllable from
a single headend controller module).
•
Frequency mode/Table of channels
Using this menu, the user can select one of the