Televes T.0X DVBS2-COFDM CI TWIN MUX 3TP(2SAT):2CH - Manual (Page 18)

MUX DVBS2_QAM/COFDM CI Twin
18
become the actual value to take into account,
which may vary slightly from the estimate.
Note: Whenthenumberofservicesexceeds100,itis
displayed the list of services and occupation
alternately, due to the limited space on the
programmingunit.
•
Service name
•
Service filtering status. Choices are OFF, ON1,
ON2, DCY1, DCY2.
» ON1, ON2 : The service passes straight forward
to the output 1 or 2, without changes.
» OFF The service is not allowed to go through
to the output.
» DCY The service goes through to the output
1 or 2 and also request its unscrambling
to the module of conditional access if it
is available. A sign of admiration (!) will
appear in this condition, when for the
position in which the CAM is situated
is impossible to decrypt it. If the CAM is
located at the output 1 DCY2 option will
not be allowed.
There are two ways to move from one service to
another:
I. First, by short presses on the key, move the
cursor to the service name; then use keys
and to move up/down among services.
When using the key from the last service of
one of the inputs, it is automatically displayed
the first service of the following input and
amended the top identifier (A, B, C) in order
to indicate, at all times, which is the input that
provides the current service.
II. Direct access to the services of a particular input
by selecting the identifier of one of the A/B/C
inputs, and again making use of keys and .
Thereby, by pressing key A or B it is
accessed the first or last service of the input,
respectively. Proceeding this way, once
located the services of the desired input,
just place the cursor on the name of the
service to get access to the rest of the list.
If any input is not available, the screen will
display “Unlock” when trying to access its list
of services.
ASERV
Unlock
ASERV
Unlock
Within the service menu, you can get access to
the advanced PID menu by a long press on key
(more than 2 sec). This option shows the list of PID
belonging to the service that was displayed on the
standard menu.
Be aware that it should be used carefully and may
need to know the characteristics of the input
transport stream for proper configuration.
This is because the PIDs of a service are subject
to changes, and if this happens the values set in
this menu may no longer be valid and therefore
unwanted behaviors can occur at the output.
Come back to the service menu by a long press on
key.
5.1.e.1 PIDs menu
To access this menu, within the service menu make
a long press on key. Make again a long press on
key to return to service menu.
Choose a service and then select the action to be
carried out with its PIDs.
The main use of this menu is to remove an audio
streaming (for those services that have more than
one audio) or other service information (teletext,
private data, ...) so that you can reduce the output
occupation.
In the case of having a CAM module, it is possible
to reduced the capacity used, and allowing
sometimes increasing the number of services that
can be unscrambled:
ASID 29800
PID 1/5
160 *video
DCY
BSID 29805
PID 3/5
162 a spa
*DCY
ASID 29800
PID 1/5
160 *video
DCY
BSID 29805
PID 3/5
162 a spa
*DCY
The available information in this menu is the
following:
•
Identifier of the input from which comes the
service (A, B, C).
•
Identifier of the service to be configured (SID
Service id).
•
PID index and total number of them available
in the service (in above examples: 1/5 and 3/5).
•
PID identifier (in above examples: 160 and 162).