CRU RAX210-SJ - Manual

RTX220 QR - Manual
RAX™ 2-BAY Quick Start Guide
1. Installation Steps
1.1 HDD Installation for RAX210
a. Pull on the ejection handle and open the door.
b. Slide in your SATA hard drive, connector-end first.
c. Shut the door.
1.2 HDD Installation for RAX211 and RAX 212
a. Slide the drive carrier out of RAX.
b. The carrier’s cover is held in place by a screw on
the rear of the carrier. Remove the screw, then
remove the cover.
c. Slide the drive in from the front of the carrier.
d. Mate the connection on the drive with the connection on the drive carrier circuit board.
e. Flip the drive/carrier assembly over, and secure the drive in place with the provided
screws.
RAX is a trademark of CRU Acquisitions Group, LLC. Other marks are the property of their respective owners. © 2010 CRU Acquisitions Group, LLC. All rights
reserved.
Limited Product Warranty
CRU-DataPort (CRU) warrants RAX to be free of significant defects in material and workmanship for a period of two years from the original date of purchase. CRU’s
warranty is nontransferable and is limited to the original purchaser.
Limitation of Liability
The warranties set forth in this agreement replace all other warranties. CRU expressly disclaims all other warranties, including but not limited to, the implied war-
ranties of merchantability and fitness for a particular purpose and non-infringement of third-party rights with respect to the documentation and hardware. No CRU
dealer, agent, or employee is authorized to make any modification, extension, or addition to this warranty. In no event will CRU or its suppliers be liable for any costs
of procurement of substitute products or services, lost profits, loss of information or data, computer malfunction, or any other special, indirect, consequential, or
incidental damages arising in any way out of the sale of, use of, or inability to use any CRU product or service, even if CRU has been advised of the possibility of such
damages. In no case shall CRU’s liability exceed the actual money paid for the products at issue. CRU reserves the right to make modifications and additions to this
product without notice or taking on additional liability.
FCC Compliance Statement: “This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at this own
expense.
In the event that you experience Radio Frequency Interference, you should take the following steps to resolve the problem:
1) Ensure that the case of your attached drive is grounded.
2) Use a data cable with RFI reducing ferrites on each end.
3) Use a power supply with an RFI reducing ferrite approximately 5 inches from the DC plug.
4) Reorient or relocate the receiving antenna.
A9-210-0008-1 Rev. 1
Host Interfaces • RAX “SJ” models: dual eSATA
• RAX “SV” models: single port-multiplied eSATA
• RAX “NJ” models: SFF-8470 multi-lane SAS/SATA 3Gb/s
• RAX “XJ” models: SFF-8088 multi-lane SAS/SATA 6Gb/s
Drive Types Supported 3.5-inch SATA (Serial-ATA) hard drives
Operating System
Requirements • Windows XP, Vista, Windows 7
• Mac OS X
• Linux distributions that support the connection type
Encryption (RAX212 model only) Full disk hardware encryption, AES 128/256
Power Supply Input: 100-240VAC, Output: 220 Watts
Cooling Fan Dual 40mm exhaust fans
Shipping Weights 17 pounds without drives
23 pounds with drives
Dimensions 429mm W x 413mm D x 44mm H
Support We don’t want anything to go wrong with your CRU-Dataport product. But if it does,
Technical Support is standing by and ready to help. Contact Technical Support through
cru-dataport.com/support or call (800) 260-9800.
For the full user manual and more information about this product, please visit www.cru-dataport.com
Models Covered:
RAX210-NJ, RAX210-SJ, RAX210-SV, RAX 210-XJ, RAX211-SV, RAX211-NJ, RAX211-XJ,
RAX212-SV, RAX212-SJ, RAX219-NJ. RAX219-XJ, RAX219-SV, and RAX219-SJ.
NOTE: The drive’s label should be facing up.
FOR OFFICE OR COMMERCIAL USE