beautypg.com

Operation – Ryobi RP4011 User Manual

Page 3

background image

3

OPERATION

OPERATION

Do not attempt to use this product if the battery cover is not securely

closed.

TURNING THE INSTRUMENT AND LASER ON/OFF

See Figure 3, page 13.

Press the

ON/DIST key at the center top of the keypad. The instru-

ment and the laser will turn on.

The laser will turn itself off after 1 minute of inactivity.

The instrument will switch off automatically after three minutes of

inactivity.

To turn the laser off, press the

CLR/OFF key at the bottom center

of the keypad. To turn the instrument off, press and hold the

CLR/

OFF key.

MAKING ACCURATE MEASUREMENTS

To increase the accuracy of measurements, follow these helpful tips.

Limit the range of measurement to 98.43 ft.

Aiming at glossy surfaces may deflect the laser beam, and affect

accuracy.

Colorless liquids, dust-free glass, Styrofoam, or other semi-

permeable surfaces may cause measurement errors.

Periodically perform test measurements, especially after extended

use and before, during, and after critical measurements.

LCD DISPLAY

See Figure 4, page 13.

Laser is ON

Reference Point Measuring (front and rear)

Pythagoras Indicator

Area/Volume

Battery Status

Units with Exponents (2/3)

Intermediate Line

Current Measurement/Summary Line

Info

REFERENCE SETTING

See Figure 5, page 13.
The default reference setting is from the rear of the instrument. To change

the setting to the front, press and release the

REFERENCE/UNITS key

on the upper left of the keypad until it shows the desired reference point.

TAKING MEASUREMENTS

See Figure 6, page 14.

Single Distance Measurement

Press the

ON/DIST key once to turn the laser on.

Press again to measure and display the distance.

Units of Measure

Press and hold the

REFERENCE/UNITS key for 3 seconds. Continu-

ously pressing and holding the key will display the same measure-

ment in meters, feet/inches, and inches only.

TRACKING

See Figure 7, page 14.
The tracking message appears as lowercase “

trc” in the LCD display.

This indicates that the laser is beamed at a surface or object that re-

quires a longer time frame to read accurately. If you continue to receive

this message, try to get a reading from a more direct angle or a more

solid surface.

FUNCTIONS

Distance Addition/Subtraction

See Figures 8 - 10, page 14.

Take a distance measurement.

Press the [

+

] key. The next measurement you take will be added to

the previous one.

Press the [

-

] key. The next measurement you take will be subtracted

from the previous one.

Repeat these steps as many times as desired. The result will be displayed

in the summary line. The value to be added or subtracted is displayed

in the intermediate line.

Press the

CLR/OFF key to cancel the last step.

Area

Press the

MODE key. The [ ] symbol is displayed.

Press the

ON/DIST key to take the first distance measurement (for

example, length).

Press the

ON/DIST key to take a second measurement (for example,

width).

The area measurement will be displayed in the summary line. The second

measurement is displayed in the intermediate line.

Volume of a Space

Press the

MODE key twice. The [ ] symbol is displayed.

Press the

ON/DIST key to take the first distance measurement (for

example, length).

Press the

ON/DIST key to take a second measurement (for example,

width).

The result of the area measurement from the values already measured

is displayed in the summary line.

Press the

ON/DIST key to take a third distance measurement (for

example, height). The value is displayed in the intermediate line.

The result of the area measurement is displayed in the summary line;

the previously measured value is displayed in the intermediate line.

Indirect Measurement

See Figure 11, page 14.
The laser distance measure uses the Pythagorean method (a

2

+ b

2

= c

2

)

to calculate distances that are otherwise difficult to access.
These instructions must be followed exactly for best results.

All target points must be vertical or horizontal surfaces.

The instrument should be rotated around a fixed point.

Indirect measurement using 2 auxiliary measurements:

Press the

MODE key three (3) times. The [ ] symbol is displayed.

The horizontal distance to be measured flashes in the symbol.

Press the

ON/DIST key to measure the horizontal distance.

The hypotenuse distance to be measured flashes in the symbol.

Press the

ON/DIST key to measure the hypotenuse distance.

The result will be displayed in the summary line.