Denon DRA-F101 - Manual (Page 13)

13
ENGLISH
8 LISTENING TO RADIO
(1) Tuning
1
Press the power operation switch to turn on the
power.
2
Press the BAND button on the tuner to select
the FM AUTO.
PHONES
SYSTEM
VOLUME
ON / STANDBY
AM-FM STEREO RECEIVER DRA-F101
SOURCE DIRECT BAND UP DOWN TUNING MEMORY / SET FUNCTION TIMER TONE DISPLAY
2 3
1
Example: Tuning in FM 92.50 MHz
(AM stations are tuned in using the same procedure.)
Auto Tuning
• When a program being broadcast in stereo is
received, the “STEREO” indicator lights and the
program is received in stereo.
• If reception is poor and there is much noise in the
stereo signals, press the BAND button to set the FM
MONO mode.
• When one of the TUNING UP/DOWN button is
pressed, the frequency changes in steps of 100 kHz
in the FM band, 10 kHz in the AM band.
• If one of the TUNING UP/DOWN button is held for
over 1 second, the frequency continues to change
when the button is released (auto tuning) and stops
when a station is tuned in. Tuning will not stop at
stations whose reception is poor.
• To stop the auto tuning function, press the TUNING
UP/DOWN button once.
NOTE:
A humming sound may be heard when using a TV
nearby while receiving AM programs. If this happens,
move the system as far from the TV as possible.
3
Use the TUNING UP/DOWN button to tune the
frequency to 92.50.
This lights when a station is tuned in.
[2] Setting the loudness mode
1
2
Press the TONE or MODE button to display
“LOUDNESS”.
Either turn the FUNCTION dial on the main unit
or use the remote control unit’s SELECT
buttons.
TONE
(Main unit)
MODE
(Remote control unit)
FUNCTION
VOLUME
/SELECT
(Main unit) (Remote control unit)
• To set to “ON”:
Turn the dial clockwise (,) or press the D
button.
To set to “OFF”:
Turn the dial counterclockwise (.) or press
the
H button.
• The mode switches as shown at the left each
time the button is pressed.
✽ “LOUDNESS” cannot be selected when the
source direct mode is on.
(OFF) (ON)
(ON)
(OFF)
[3] Adjusting the balance
1
2
Press the TONE or MODE button to display
“BALANCE” (Refer to page 12.)
Either turn the FUNCTION dial on the main unit
or use the remote control unit’s SELECT
buttons.
TONE
(Main unit)
MODE
(Remote control unit)
FUNCTION
VOLUME
/SELECT
(Main unit) (Remote
control unit)
• If the volume of the right speaker is low:
Turn the dial clockwise (,) or press the D
button.
If the volume of the left speaker is low:
Turn the dial counterclockwise (.) or press
the
H button.
• The balance can be set to “CENTER” or
adjusted within the range of +1 to +10 in
steps of 1. When set “CENTER”, the
difference between the volume of the left and
right speakers is 0.
✽ “BALANCE” cannot be selected when the
source direct mode is on.
(left channel
volume
adjustment)
(right
channel
volume
adjustment)
(left channel
volume
adjustment)
(right
channel
volume
adjustment)
CLEAR
1 2 3
5 4 6
7 8 9
10 +10
CD SRS MD TAPE
TUNING
REPEAT
CALL
PROG / DIRECT
RANDOM
BAND RDS
DIMMER TIME/ PANEL
TIME EDIT
SYSTEM POWER
OFF ON
STOP PLAY VOLUME /SELECT
1
3
2
(Main unit)
SYSTEM
ON / STANDBY
SYSTEM
POWER
ON
(Remote control unit) (Main unit) (Remote control unit)
(Main unit) (Remote control unit)
BAND BAND
UP DOWN
TUNING
TUNING