Q&Q QUARTZ L105J - Manual (Page 2)

counting
time
starting value (hour, mintue)
Timer 4 Display Timer 3 Display
Timer 1 Display Timer 2 Display
Countdown Timer Mode
[L/R]
[L/R] [L/R]
[L/R]
Timer 1*
Timer 3*
Multi-Timer Counting Sequence
Timer 2*
Timer 4*
D If Timer 1, 2, 3 or 4 which set 0:00 as the
starting value, that timer will be excluded
from the counting sequence.
7.0 Chronograph Mode - Chronograph Mode
3. Lap times
time
[S/S]
[S/S]
[S/S]
[S/S]
[L/R] [L/R] [L/R]
[S/S] [S/S]
[S/S]
0 10 20 30
30 0
20
10 10 10 0
10 0 10
lap 1 lap 2 lap 3
2. Accumulative elapsed time
1. Elapsed time
Elapsed time, Accumulative
Elapsed time and Lap time
Chronograph Display
'All Zero'
accumulative
running time
(1/100 second)
accumulate
running time
(second)
accumulative
running time
(minute)
accumulative
running time
(hour)
current lap
running time
Chronograph Mode
+ This Watch includes a stopwatch function which measures:
+ Elapsed time, accumulative elapsed time (multi-phase elapsed time)
and Lap time (get a elapsed time without stopping the counting).
+ The measuring capacity of the chronograph:
+ Measuring unit: 1/100 second,
+ Measuring range: 9 hours, 59 minutes and 59.99 second,
+ Lap Memory: a maximum of 50 laps.
Chronograph Display
+ When the Chronograph Display is selected, the Watch will show the
following items on the display:
+ During the chronograph is counting: The current lap time and the
accumulative elapsed time is exhibited on the 1st and 2nd row
respectively. NOTE: The current lap time will be the same as the
accumulative elapsed time for lap 1.
+ During the chronograph is stopped: The current lap time and lap
number are exhibited on the 1st row, and the accumulative elapsed
time is exhibited on the 2nd row.
+ During the Lap Display is displaying: The current lap number and
the lap time is exhibited on the 1st and 2nd row respectively.
7.1 Chronograph Mode - Using the Chronograph
Counting Display
[L/R] 5 seconds
Lap Time Display
Stop Counting Display
hold [L/R]
elapsed
time
(counting)
elapsed
time
(stop
counting)
[S/S]
[S/S]
All Zero Display
lap time
lap
number
How to Measure Elapse Time
+ During the 'All Zero' Display, press the [S/S] button once will start
the counting, and press the [S/S] button again will stop the
counting.
+ The elapsed time between the above 2 key-stokes will be
exhibited on the 1st row of the display. Repeat the above key
operations to get the accumulative elapsed time.
How to Get a Lap Time
+ When the chronograph is counting, press the [L/R] button to get
and view the Lap Display for 5 seconds. In the Lap Display, the
current lap number and lap time will appear on the 1st and 2nd
row of the display respectively.
+ After the 5 seconds, the Watch will return to counting display
automatically. Then the new lap time and the accumulative
elapsed time will be exhibited on the 1st and 2nd row of the
display respectively. Repeat the above key operations to get
another lap time.
How to Recall/Reset the Lap Time
+ During the chronograph is stopped:
+ Press the [L/R] button one by one to review the recorded lap
times, or
+ Hold down the [L/R] button for about 2 seconds to clear the lap
time, and reset the display to 'All Zero' display.
8.0 Countdown Timer Mode - Countdown Timer Display
Countdown Timer Mode
+ This Watch includes 4 countdown timers. They are Timer 1, 2, 3 and 4.
Using one timer (Single Timer) which can run normal timer function. But
combines two or more timers (Multi-Timer) can extend the timer function to
measure multi-phase elapse time.
+ The measurement unit of these timers is 1 second, and the starting value of
these timers can be set up to a maximum of 23 hours and 59 minutes.
+ When a timer which set 0:00 as the starting value, that timer will be excluded
from the counting sequence.
+ When the timer is started, the Watch will count repeatingly unless it is
stopped by pressing the [S/S] button. During the counting, the Watch will
beep once when a timer counts to the last 1 and 0 second
Single Timer and Multi-Timer
+ When using Single Timer (one timer), it must excludes other timers from the
counting sequence by setting their starting value to 0:00.
+ When using Multi-Timer, it is counting on a sequence which starts the
counting from Timer 1 to another timers following the adjacent diagram.
How to Select Different Timer Display
+ To select different countdown timer display during the timer is stopped, press
the [L/R] button one by one following the adjacent diagram.
8.1 Countdown Timer Mode - Setting the Countdown Timer
Countdown Timer Display
minute
hour
Setting Sequence
[S/S]
hold [M] [M]
Increase
the number
increase
the number
at a higher
speed
[L/R]
hold [L/R]
How to Set the Countdown Timer
+ The following paragraphs will illustrate the procedure for
setting the timer 1. Even so, setting the other timers will work
on the similar procedure.
+ To select the setting display, hold down the [M] button for 2
seconds in the Timer 1 Display, and then the 'Minute' digits
start flashing on the display.
+ In setting display, press the [S/S] button to move the flashing
following the adjacent diagram to select among different
settings.
+ When one of the settings (minute, hour) is flashing, press the
[L/R] button to change the number (hold down the button to
change the number at a higher speed).
+ When the setting is completed, press the [M] button once to
exit the setting display. The Watch will also exit the setting
display if NO key-stoke has been activated for 1 minute.
8.2 Countdown Timer Mode - Loading and Resetting the Timer
Countdown Timer Display
Stop Counting
hold
[L/R]
hold
[L/R]
load the
timer(s)
into the
counting
sequence
reset all
starting
values
to zero
[L/R]
Confirm
the loading
or
resetting
Abort
the loading
or
resetting
[M]
[L/R]
How to Load the Timers
+ If the starting value has been set for the timer(s), they must be
loaded into the counting sequence before it is ready for
counting.
+ To load the timer(s) into counting sequence, hold down the [L/R]
button in Timer Display (when the timer is stopped) until the 'Ld
ALL' indicator appeared following the adjacent diagram.
+ When the 'Ld ALL' indicator is appeared, press the [M] or [L/R]
to confirm or abort the loading.
+ If the Timer Display is returned after the loading, the timer(s) is
ready to count.
How to Reset the Timers
+ During the 'Ld ALL' indicator is appeared, hold down the [L/R]
button until the 'cLR ALL' indicator appeared following the
adjacent diagram.
+ When the 'cLR ALL' indicator is appeared, press the [M] or
[L/R] to confirm or abort the resetting.
+ If the Timer has been reset, all starting values will be reset to
0:00.
8.3 Countdown Timer Mode - Using the Single Timer
How to Use the Single Timer
+ When using one timer only (Single Timer), excludes other
timers by setting their starting values to 0:00.
+ Once the starting value has been set for the last timer, it must
be loaded into the counting sequence before it is ready for
counting. Check previous chapter 8.2 for more detail on how
to load the starting value into the counting sequence.
+ Press the [S/S] button to start the counting. The counting will
be restarted automatically when it reaches zero unless the
counting is stopped by pressing the [S/S] button.
How to Re-load the Timer
+ To re-load the timer to its original starting value during the
timer is stopped, perform the loading process following the
previous chapter 8.2.
Timer Alarm Sound
+ During the counting, the Watch will beep once when a timer
counts to the last 1 and 0 second.
Timer 1 Display Counting Display
Counting
Display Counting Display
Zero Display
[S/S]
[S/S]
[S/S]
[M]
hold
[L/R]
Stop Counting Display
stop
counting
counting
beep, beep
8.4 Countdown Timer Mode - Using the Multi-Tmer
9.0 Dual Time Mode - Dual Time Mode
9.1 Dual Time Mode - Setting the Dual Time
10.0 Specifications
Countdown Timer
+ Timer: 4 timers
+ Resolution: 1 second
+ Measuring Range: 23 hours 59 minutes
+ Timer Sounds: the Watch will beep once
when a timer counts to the last 1 and 0
second.
Pacer Mode
+ Setting Range: 40 bpm to 180 bpm
+ Setting step: 5 bpm
Dual Time Mode
+ Time System: AM, PM, Hour, minute, second
Current Time Mode
+ Time System: AM, PM, Hour, minute,
second
+ Time Format: 12-hour or 24-hour format
+ Calendar: Month, date and day of week
display (Auto-Calendar function for leap year
and day of week)
Alarm Mode
+ Daily alarm and hourly chime
+ Alarm sound: 20 seconds
Chronograph Mode
+ Resolution: 1/100 second
+ Measuring Range: 9 hours 59 minutes 59.99
seconds
+ Lap memory: 50 lap memories
Dual Time Mode
minute
hour
Setting Sequence
[S/S]
hold [M] [M]
Increase
the number
increase
the number
at a higher
speed
[L/R]
hold [L/R]
To Set the Dual Time
+ To select the setting display, hold down the [M] button for 2
seconds in the Dual Time Mode, and then the 'Minute' digits
start flashing.
+ In the setting display, press the [S/S] button to select the
flashing (setting item) as shown in the diagram.
+ When one of the settings (minute, hour) is flashing, press the
[L/R] button to change the number; hold down the button to
change the number at a higher speed.
+ When the setting is completed, press the [M] button once to
exit the setting display. The Watch will also exit the setting
display if NO key-stoke has been activated for 1 minute.
Dual Time Mode
dual time
(second)
dual time
(minute)
dual time
(hour)
Dual Time Mode
+ This Watch includes a dual time which show the current
time of the second time zone.
+ The second digits are same as the one of current time.
Dual Time Display
+ When the Dual Time Display is selected, the dual time
(hour, minute, second) is exhibited on the 2nd row of the
display.
hold [L/R]
hold
[L/R]
Reset the
Starting Values
Load the
Starting Values
Confirm
the loading
or
resetting Abort
the loading
or
resetting
[M] [L/R]
Timer 1*
Timer 3*
Multi-Timer Counting Sequence
The counting
is stopped
Timer 2*
Timer 4*
D If timer 1, 2, 3 or 4 which set 0:00 as the
starting value, that timer will be
excluded from the counting sequence.
[S/S]
[S/S]
beep, beep
beep,
beep
beep,
beep beep, beep
How to Use the Multi-Timer
+ To use the Multi-Timer function which combines two or more
timers to measure multi-phases elapse time, it must set the
starting value for each timer.
+ Once the starting value has been set for the timer(s), they
must be loaded into the counting sequence before it is ready
for counting. Check the previous chapter 8.2 for more detail on
how to load the timer into the counting sequence.
+ Pressing the [S/S] button will start the counting sequence. The
Multi-Timers will starts the counting from Timer 1 to another
timers following the adjacent diagram. Pressing the [S/S]
button once again will stop the counting.
+ The Watch will count repeatingly unless it is stopped by
pressing the [S/S] button.
Timer Alarm Sound
+ During the counting, the Watch will beep once when a timer
counts to the last 1 and 0 second.
How to Re-load/Reset the Starting Values
+ To re-load or reset the Starting Values during the timer is
paused, perform the loading or resetting process which
mentioned in the adjacent diagram to re-load or reset the
starting vales.
Setting Sequence