Labconco CentriVap Refrigerated Centrifugal Concentrators 7310000 Series - Manual (Page 28)

Chapter 6: Accessories for Your CentriVap
Product Service 1-800-522-7658 24
1467700 Vacuum Pump – 195 liters/minute capacity with gas ballast. Ultimate pressure 1.3 x 10 -4
mBar. 115 VAC, 60 Hz, single phase, 7.8 amp.
1472100 Vacuum Pump – 117 liters/minute pumping capacity with gas ballast. Ultimate pressure 1.3
x 10
-4 mBar. 115 VAC, 60 Hz, single phase, 4.6 amp.
7739402 Vacuum Pump – 117 liters/minute. Same as 1472100 except 220/208-230 VAC, 50/60 Hz,
single phase, 2.4 amp operation.
7739403 Vacuum Pump – 195 liters/minute. Same as 1467700 except 220/208-230 VAC, 50/60 Hz,
single phase, 4.0 amp operation.
1473400 Pump Exhaust Filter – Disposable filter that removes visible oil mist and odor from vacuum
pump exhaust. Fits vacuum pumps 1467700, 1472100, 7739402 and 7739403
1473200 Replacement Element, Oil Mist, Pump Exhaust Filter – Fits pump exhaust filter 1473400.
1473300 Replacement Element, Odor, Pump Exhaust Filter, package of 5 – Fits pump exhaust filter
1473400 or vacuum pumps 1472100, 1467700, 7739402 and 7739403.
1988000 Vacuum Pump Oil, 1 Liter – A molecularly distilled hydrocarbon oil low vapor pressure.
For vacuum pumps 1467700, 1472100, 7739402 and 7739403.
7393000 Vacuum Pump – 75 liters/minute @ 50Hz, 82 liters/minute @ 60Hz
Ultimate pressure < 2 mBar, 115V, 50/60 Hz, 3.5 Amp
7393001 Vacuum Pump – 75 liters/minute @ 50Hz, 82 liters/minute @ 60Hz
Ultimate pressure < 2 mBar, 230V, 50/60 Hz, 2.0 Amp
7539902 Vacuum Pump – 200 liters/minute @ 60Hz, 183 liters/minute @ 50Hz
Ultimate vacuum < 1x10
-3 mBar, 230V, 50/60 Hz
7584000 Vacuum Pump – 110 liters/minute @ 60Hz, 96 liters/minute @ 50Hz
Ultimate vacuum < 2x10
-3 mBar, 115V, 50/60 Hz
7584002 Vacuum Pump – 110 liters/minute @ 60Hz, 96 liters/minute @ 50Hz
Ultimate vacuum < 2x10
-3 mBar, 230V, 50/60 Hz
7456600 Glass Lid for Concentrator – Direct replacement for standard equipment acrylic lid. For use
with chemicals that could craze acrylic.
7464300 CentriZap ™ Strobe Light – For observing samples while the rotor is spinning.
Installing a Glass Lid
Turn off the CentriVap. Pull outward on the hinge pin knob. Lift and remove the
old lid. To install the new lid, reverse the process.
Installing a Vacuum Gauge
A user-supplied vacuum gauge may be attached to the CentriVap to monitor the
vacuum level. Attach the vacuum gauge to the barb end of the Quick Disconnect
Coupling fitting that was supplied with the CentriVap using a length of suitable
rubber hose. The Quick Disconnect Coupling fitting can then be pushed into the
mating connector on the left side of the CentriVap located towards the rear. The
Quick Disconnect Coupling fitting can be removed from the mating connector by
pressing on the tab on the connector and then pulling out the insert fitting. Always
remove the Quick Disconnect Coupling from the CentriVap when a vacuum
gauge is not attached to it.