beautypg.com

Fly high with hitec, Receiver, Servos – HITEC Sky Scout (KIT) User Manual

Page 3: Charger, Battery & esc, Motor

background image

3

Fly high with Hitec

Section One:

Recommended Equipment (sold separately)

The KIT version of the Sky Scout only includes the airframe, associated hardware, along with the prop and spinner assembly. The following additional

parts and equipment are needed to complete the assembly. Visit a Radio Control Hobby shop or consult an experienced flier about purchasing the right

equipment for your needs.

1. 3-4 Channel Aircraft Radio

The Sky Scout requires at least a 3-channel radio to fly. Adding the

optional ailerons requires a 4th channel, though a 5 or higher channel

radio with mixing features will allow for additional flight performance.

We recommend Hitec models such as the Optic 5 or Optic 6 Sport for

optimal operational performance
2. Receiver

We recommend at least a 5 channel aircraft receiver that matches your

radio system for maximum flexibility. Models such as the Hitec Minima

6T or 6S will fit this need if you are using a Hitec brand 2.4 GHz Radio.
3. Servos

You will need at least two Sub Micro servos to complete your model. If

you choose to add the optional ailerons you will need an additional two

sub-micro servos. Hitec recommends using the HS-55 or HS-5055MG

on all surfaces. These servos are available at most Radio Control

Hobby stores.
4. Motor

You will need a brushless outrunner motor designed for aircraft use.

We recommend the minimum of a 200-watt 1100Kv motor. The motor

dimensions need to be no more than 28mm in diameter and 28mm in

length. To avoid having to use a special adapter make sure the output

shaft is either 3 or 3.2 mm in diameter. The Sky Scout Kit contains Prop

adapters in both of these sizes.
5. ESC

You will also need an Electronic Speed Control with built in BEC that is

suitable for the motor you purchased. Hitec recommends using an ESC

with a minimum rating of an 18A and a BEC output of at least 1.5 amps
6. Battery & Charger

For optimal performance Hitec recommends a 3-cell 11.1V 1300mAh

LiPo battery with at least a 15C discharge rating. You will also need a

charger capable of charging this battery as well. tions you are using.

3-4 CH AIR TX

1

RECEIVER

2

SERVOS

3

Section One:

Other Sky Scout Versions

Radio, Receiver and Power Set Components for Each Version

(READY TO GO) stock# 13207

This version includes everything you need to fly your Sky Scout after a few easy assembly steps.

Semi-assembled model

Semi-assembled model

Hitec Lite 4 2.4GHz 4-channel Radio (w/4AA aIkaline batteries)

Hitec Minima 6S Receiver (installed)

Hitec HS-55 Servos (installed)

(HITEC TO GO) stock# 13209

This version allows you to fly your Sky Scout with the Hitec radio you already have or may wish to purchase. Any of Hitec’s

AFHSS 2.4GHz radios, or radios using a Spectra 2.4GHz module, can be linked with the Minima 6S included in the H2GO set.

Semi-assembled model

Hitec Minima 6S Receiver (installed)

Hitec HS-55 Servos (installed)

C2812-1100 Brushless Outrunner Motor (installed)

(PLUG-IN TO GO) stock# 13210

This Sky Scout version is for modelers who already own the additional products needed for flying. A transmitter, receiver,

charger and suitable batteries are required needed to fly the model plane.

Semi-assembled model

Hitec HS-55 Servos (installed)

C2812-1100 Brushless Outrunner Motor (installed)

Hitec HBE-18A ESC (installed)

C2812-1100 Brushless Outrunner Motor (installed)

Hitec HBE-18A ESC (installed)

HLP-3S 1300mah Li-Po battery (included)

CG-115 DC Balancing Charger (included)

Hitec HBE-18A ESC (installed)

HLP-3S 1300mah Li-Po battery (included)

CG-115 DC Balancing Charger (included)

CHARGER

6

BATTERY &

ESC

5

MOTOR

4