Bullard Magma - Manual (Page 4)

Americas:
E.D. Bullard Company
1898 Safety Way
Cynthiana, KY 41031-9303
Toll free: 877-BULLARD (285-5273)
Tel: 859-234-6616
Fax: 859-234-8987
www.bullard.com
Europe:
Bullard GmbH
Lilienthalstrasse 12
53424 Remagen • Germany
Tel: +49-2642 999980
Fax : +49-2642 9999829
www.bullardextrem.com
Asia-Pacific:
Bullard Asia Pacific Pte. Ltd.
LHK Building
701, Sims Drive, #04-03
Singapore 387383
Tel: +65-6745-0556
Fax: +65-6745-5176
www.bullard.com
6029009296D (0713)
ISO 9001
certified
Accessories and Replacement Parts
When fitted with another item of personal protective equipment or with an accessory (other than as supplied by the helmet manufacturer for use with this helmet) a helmet marked as complying with
EN443 might no longer satisfy all clauses of the standard.
All accessories and replacement parts are designed for the use with your Bullard Magma helmet.
Do not use them separately or with other brand or model helmets. Do not use any accessories or replacements parts other than listed below.
0299
Notified Body:
0299
FA PSA Prüf- und Zertifizier-
ungsstelle
Zwengenbergerstrasse 68
42781 Haan
R965 R966 R967 R968 R969 R970 R973
Plate Kit Connector Kit Logo Kit Chinstrap Kit Crown strap kit Mask Adapterkit Screw kit
Assembly and cover
plate R/L with screws
Sleeve and washer R/L
with screws
Bullard Logo with O-ring
and screw
Chin strap with screws
Crown straps and
connector strap with
hangers
Mask Adapter R/L with
screws
Complete set of screws
List of accessories and replacement parts
R950 Visor
R957 Napeband
R958 Browband
R959
Brow Pad
R160 Ratchet Cover
R951 Eye Protector
R960 Neck Protector
R961 Dutch Neck Protector
R952 Visor Gold Plated
R992 Hanger Loop Han´n Go
R993 Torch Bullard 2AA
R994 Torch Bullard 2AAA
R995 Chin Cup Strap
R996 Nomex Hood
Accessories and replacement parts are subject to technical changes and completion. Please
check www.bullardextrem.com for latest information
Colors
Lumenescent Yellow, Yellow 1018, Fluorescent Yellow 1026, Fluorescent Red 2005, Red 3020,
Green PMS 362, Blue 5015, White 9016, Black 9004, Silver 9006.
Certification
Your helmet has been tested and certified according to EN443:2008, visors according to
EN14458:2004, goggles according to EN166 .
The helmet is suitable for structural fire fighting and Hot Training.
Hot Trainings can damage the helmet which is not covered by the regular warranty. It is
recommended to provide separate helmets dedicated to Hot Training and use Nomex hoods.
Options and Marking
Option Marking
Electrical properties classification
- wet helmet insulation test according to 6.8.2
- surface insulation test according to 6.8.2
E2
E3
Classification Low temperature: -40°C ****
C: Classification liquid chemicals NaOH, HCe, H
2
SO
4
, O-Xylen
WARNING
The Helmet absorbs the energy of a blow by partial destruction of, or damage to, the helmet. Even though such damage may not be readily apparent, any helmet subjected to a
severe impact should be replaced. The protection provided by a helmet depends on the circumstances of an accident, and wearing a helmet cannot always prevent serious or
even fatal injuries or long-term invalidity. The safety intended to be provided by the helmet can only be ensured when it is properly assembled and correctly fitted. Removable
parts shall not be worn separately.
Always wear a correctly-adjusted helmet and straps, and always bear in mind that a helmet cannot protect the neck area or other unprotected areas of the head.
Ensure that wearing respiratory equipment does not affect the fit of the helmet and vice versa.
This helmet is only approved for use in fire service, rescue service and disaster control operations.
It is especially unsuitable as a sports or motorcycle helmet.
©2013 Bullard. All rights reserved.