Denon AVR-686S - Manual (Page 44)

41
ENGLISH
Advanced Setup Advanced Setup
ENGLISH
4 Press the CURSOR F F or G G button to set the
center channel level, then press the CURSOR H H
button to switch to the front R channel level
(manual mode).
5 Press the CURSOR F F or G G button to set the
front R channel level, then press the CURSOR H H
button to switch to the surround R channel level
(manual mode).
6 Press the CURSOR F F or G G button to set the
surround R channel level, then press the
CURSOR H H button to switch to the surround
back R channel level (manual mode).
7 Press the CURSOR F F or G G button to set the
surround back R channel level, then press the
CURSOR H H button to switch to the surround
back L channel level (manual mode).
Setting the Test Tone
1 • Press the CURSOR F F button to switch the test
tone mode.
• Press the ENTER or CURSOR H H button to
switch to the digital input (COAXIAL) setting.
2 Press the CURSOR F F or G G button to select the
test tone mode, then press the CURSOR H H
button to start test tone.
T . T O N E A u t o >
Auto Manual
• Use this setting to adjust to that the playback level between the
different channel is equal.
• From the listening position, listen to the test tones produced
from the speakers to adjust the level.
• The level can also be adjusted directly from the remote control
unit.
Auto:
Adjust the level while listening to the test tones produced
automatically from the different speakers.
Manual:
Select the speaker from which you want to produce the test
tone to adjust the level.
3 Press the CURSOR F F or G G button to set the
front L channel level, then press the CURSOR H H
button to switch to the center channel level
(manual mode).
A U T O - F L
F L V O L 0 d B
-12dB 0dB +12dB
* T E S T T O N E Y e s <
8 Press the CURSOR F F or G G button to set the
surround back L channel level, then press the
CURSOR H H button to switch to the surround L
channel level (manual mode).
9 Press the CURSOR F F or G G button to set the
surround L channel level, then press the
CURSOR H H button to switch to the subwoofer
channel level (manual mode).
10 Press the CURSOR F F or G G button to set the
subwoofer channel level, then press the ENTER
button to finish the test tone.
11 Press the ENTER or CURSOR H H button to switch
the Digital In Assignment (COAXIAL) setting.
• When adjusting the level of an active subwoofer system, you
may also need to adjust the subwoofer’s own volume control.
• When you adjust the channel levels while in the system setup
channel level mode, the channel level adjustments made will
affect all surround modes. Consider this mode a master
channel level adjustment mode.
• After you have completed the system setup channel level
adjustments, you can then activate the individual surround
modes and adjust channel levels that will be remembered for
each of those modes. Then, whenever you activate a particular
surround sound mode, your preferred channel level
adjustments for just that mode will be recalled. Check the
instructions for adjusting channel levels within each surround
mode (
page 28).
2 Adjusting the test tone
• Before playing with the surround function, be sure to use the
test tones to adjust the playback level from the different
speakers. This adjustment can be performed with the system
setup or from the remote control unit, as described below.
• Adjusting with the remote control unit using the test tones is
only possible in the “Auto” mode and only effective in the
STANDARD (DOLBY/DTS SURROUND) modes. The adjusted
levels for the different modes are automatically stored in the
memory.
2 Press the TEST TONE button.
• Test tones are output from the different speakers.
3 Press the CURSOR F F or G G button to adjust so
that the volume of the test tones is the same for
all the speakers.
4 After completing the adjustment, press the
TEST TONE button again.
1 Press the STANDARD button to select the
STANDARD (DOLBY/DTS SURROUND)
modes.