Audiovox CTX5000 - Manual (Page 13)

(2) To originate a call, enter the telephone number,
then press | SND |. The microphone will be turned
on, ready for conversation when your party
answers.
After a call is completed. Press | EN^ to
terminate a call.
Note: (1) When this option is activated, as the unit
always operates in Hands-free Mode, you
should press | END | to terminate a call.
(2) Even if this option is installed, you can
of course engage the conversation via
the Handheld, but you have to press
I END I to terminate a call.
(31
When you hear feedback on a bad RF
Channel, adjust the hands-free loop
attenuation as follows.
1) Press I FUNC |, key 0 then .
Hands-free loop attenuation will be
increased by 6 dB,
2) To return to the normal condition,
press I FUNC I , key 0 then [T].
END TO END SIGNALING
This feature permits you to utilize some attractive
ways of using the phone, such as accessing
discounted long distance network, signal pager, or
banking by phone etc..
For these purpose the signalling should be in
DTMF (Touch Tone™). The following two features
will make in more easier to place call in DTMF.
Touch Tone ™ from Memory
DTMF signalling by repertory dialer is available
even while engaged in a telephone conversation.
1- Press I RCL I I RCL |, then enter the repertory
memory address.
The last ten digits of the number will appear on
the readout.
2. Press
I
SND |. Then DTMF signalling will be
placed and the DTMF tone can be monitored
through the loudspeaker.
Note: Continuous DTMF from keypad can be
manually dialed as well to access
answering machines when engaged in a
telephone call.
Link Dialing
This feature permits you to pre-set from repertory
memory or key pad up to five numbers before
originating a call. With this feature, the first
number is sent in digital form to the cell site. Then
up to four other numbers can be sent with DTMF
signalling by simply pressing |
SND [ for each
additional number.
Note: (1) Each number to be linked may be recalled
from memory or entered by key pad,
(2) Each number to be linked should be within
16 digits including linking mark “ = ” at
the end.
(3) Linked number can be stored in the
memory. However, numbers of more than 16
digits should be stored into memory
address 91 through 99,
Example: To access the Discounted Long Distance
Call, you should call Long Distance Service Office
first, and enter your ID number, then the telephone
number to be placed.
1. Recall the Telephone Number of the Long
Distance Service Office.
rr I | 7 | 4 | 6 | 3 | 4 | 7 | 9 |
2. Press I FUNC |, then .
Linking Mark “ = ” will be added after the number
placed before.
rnyj^TiTT]7T^^
3, Recall you ID number.
rrr 1 6 | 7 1 H 4 1 8 1 ^ 2 ]
4. Press iFUNCl, then [^.
m U 7 | l | 4 j ¥ [ 5 l 2 H
5. Recall the telephone number to be called.
f T Í 2 | 3 | 4 | 5 | 6 l 7 | 8 Í T r ó l
6. Press I SND i. The [ IN USE | indicator will light as
the call is placed, | Link 1 [will appear in display.
7. After you received an answer from the Long
Distance Service Office, press | SND | again. The
DTMF signal will be placed and the DTMF tone
of your ID number can be monitored through the
loudspeaker. | Link 2] will appear in display.
8. If your ID number is accepted, the Long Distance
Service Office will answer again, so press | SND |.
Then the long distance call will be placed and
the DTMF tone can be monitored through the
loudspeaker.
24 25