Poulan 169553 - Manual (Page 27)

KKOtJI.Cii UAUSt -M 1 ION
Excessi¥e¥ibrat»ii torn, bent or loose blade.
2. Bent blade mandrel.
3. Loose/damaged part(s).
Replace blade. Tightei
2. Replace blade mandrel.
3. Tighten loose part(s
Engine continues to
■|jn when operator
saves seat
with attachment
:lutch engaged
1. Faulty operator-safety presence control
systems.
1. Check wiring, swii
flections. If not cc
authorized service m nt .tofepaffrr-.r-rii
^oor cut -ynewen 1. Worn, bent or loose blade.
2. Mower deck not level.
3. Buildup of grass, leaves, and trash under
mower.
ent blade mandrel.
5. Clogged mower deck vent holes from
i.uildtip iffi/as.-o leaves, and trash around
mandtelb
1 i'
1
lace blade. Tighten blade boh
2. Level mower deck.
3. Clean underside of mower housing.
Replace blade mandrel.
5. Clean around mandrels to open vent
holes.
lower blades will
lot rotate ; •JLc4ruct»ui: M ^.iuf:h mechanism.
Worn/dani«gei mower drive belt.
E Ftozeii idloi pulley
4 f ¡nec-n blade mandrel.
1. Ri'movfr -.bsttuf lirn
2. Replrv e rroWf:r duv.i belt.
3. Replace
i JI h p.Jiey
4. Repin- ft blade rnandrcT
*oor grass discharge ., E.iyiOi- 'petfii k o ¿low.
2 Travel speed too fast.
3. Wet grass.
4. Mower deck not level.
5. Low/uneven tire air pressure.
6. Worn, bent or loose blade.
7. Buildup of grass, leaves and trash under
mower.
0 MoW( r dri' P holt worn.
9 iniprnp_,iy installed.
10 Imptopt. hi ed.
1 1
t 'cp'Kdm wf' d> ck vent holes from
bijiitJi Ip A jt le xves, and trash around
rfH'idrei
1. i la T ’•ott.i- rent,' I ir, “FAST’ position.
2. Shift to i lower speed.
3. Allow press to dry' before mowing.
4. Level mower decK.
5. Check tires for proper air pressure.
6. Replace/sharpen blade. Tighten blade bolt.
7. Clean underside of mower housing.
8. Replace mower drive belt.
9. Reinstall blades sharp edge down.
10. Replace with blades listed in this manual.
11. Clean around mandrels to open vent holes.
lead!ight{s)not
iorkingfif so
quipped)
i C wiH 111 ‘ { j
F
: I 1 I f ) Siu:iii-d j U'
J. f ttilrj I kj I i /l|IC1l I
' I M* igon wiring.
^ . 1
1. Turn switch “ON”.
2. Rtpiace bu!lj(:r).
3. Diec-S'replacfcf light switch.
4. Chftck wifiny and connections.
5. Replace fuse
attery wiii not
targe
1 ftnd b, tu-iy reiiis).
2. Poor cable connections.
3. Faulty regulator (if so equipped).
4. Faulty alternator.
1
f.r oiace battery.
2. Check/clean all connections.
3. Replace regulator.
4. Replace alternator.
ngine “backfires”
'hen tyrning engine
DFF”
; Engine throttle control not set at “SLO’
position for 30 seconds before stopping
engine.
1. Move throttle control to “SLOW” position and
allow to idle for 30 seconds before stopping
engine.
27