Ariens PRM-10000 - Manual (Page 33)

t
Part
No.
Description No.
Req'd.
Part
No.
Description No.
Req'd.
1038 Jaw Clutch 1 4X50 Seal 1
3017 Bearing Flange 1 4X51 Seal 2
10105 Gear Case 1 5X32 Snap Ring 1
10106 Gear Case Flange 1 5XK2 Snap Ring 1
10107 Bearing Spacer 1 9X7 RoU Pin 1/4 X 1-1/4 3
10108 Gasket 1 9X9 Roll Pin 1/8 X 1 1
10110 Fr(mt Gear Shaft 1 9X22 RoU Pin 5/18 X 1-3/8 1
10111 Fan 1 11X13 Pipe Plug 3/8 Sq. Hd. 2
10113 R. H. Rake 1 12X1 Cap Screw H. H. 1/4-20 x 3/4 5
10114 U H. Rake 1 12X22 Cap Screw H. H. 5/16-18 x 3/4 4
10142 Bearing Flange 5 12X23 Cap Screw H. H. 3/8-16 x 3/4 2
10154 Ccmtrol Sprocket 1 12X28 Cap Screw H. H. 1/4-20 x 1/2 6
10164 Scraper Blade 1 12X71 Shear Bolt 2
10165 Runner 2 14X12 Socket Set Screw 5/16-18 x 3/8 2
10229 Wave Washer 1 or 2 19X9 Carriage Bolt 5/16-18 x 1/2 11
10242 Sllcer Bar 1 19X10 Carriage Bolt 3/8-16 x 3/4 4
10244 Helicon Gear 1 19X11 Carriage Bolt 5/16-16 x 3/4 3
10245 Helicon Pinion Shalt 1 20X2 Lockwasher 1/4 5
10264 Blower Housing 1 20X3 Lockwasher 5/16 7
10265 Front Gear Case Support 1 20X4 Lockwasher 3/8 4
10269 Chute Clamp 3 21X2 Wrought Washer 5/16 15
10281 Chute Control Support 1 21X36 Washer .880 ID x 1.375 x 1/16 4
10284 Chute Cmitrol Crank 1 23X15 Hex Nut 5/16-18 3
10286 R. H. Rotor Shield 1 23X30 Hex Locknut 3/4-16 2
10287 L. H. Rotor Shield 1 23X39 Hex Locknut 3/8-16 6
10289 Rod Hanger 1 23X40 Hex Locknut 1/4-20 12
10290 Universal Joint 1 23X42 Hex Locknut 5/16-18 13
10291 Deflector Chute 1 23X51 Keps Nut #10-24 6
10292 Discharge Chute 1 24X1 WoodruH Key #11 1
1X44 Bearing Cup 2 25X14 Cotter Pin 1/8 X 1-1/4 1
1X45 Bearing Cone 2 LABELS NOT ILLUSTRATED
1X63 Ball Bearing 3 40X12 Sno-Thro Label 1
2X22 Flange Bushing 2 40X14 Cauti(xi Label 1
OPERATING INSTRUCTIONS
1. ATTACHING
a. Sno-Thro Attachment.
(1) Hook the notches in the lower portlcm of the
Sno-Thro Attachment frame over the rod passing
through the forward section of the tractor frame.
(2) Tip the two sections tc^ether, being sure
the jaw clutch on the Sno-Thro Attachment and trac­
tor are lined up.
(3) Insert and tighten the two 3/8-lnch cap­
screws through the top of the tractor frame and into
the Sno-Thro Attachment.
b. Chute Control Rod.
(1) Insert the rod hanger through the hole in
the upper handle bar and secure with the 1/4-inch
locknut.
(2) Fasten the chute control support to the
tractor with the hardware provided. Poslticm the
support so that the gear meshes properly with the
holes in the chute. Fasten securely.
(3) Slide the chute control rod through the rod
hanger and into the end of the universal joint. Se­
cure the rod to the universal joint with a cotter pin.
Page 33