beautypg.com

How to use your tractor, To set parkins brake (see fig. 8), Stopping (see fig. 8) – Sears 917.25667 User Manual

Page 13: To use throttle control (see fig. 8), To use choke control (see fig. 8), To move forward and backward (see fig. 8), To adjust mower cutting height (see fig. 8), To adjust gauge wheels (see fig. 9), Operation

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

background image

OPERATION

The operation of any tractor can result in foreign objects thrown into the eyes, which can result
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor
or performing any adjustments or repairs. We recommend a wide vision safety mask over the
spectacles or standard safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKINS BRAKE (See Fig. 8)

Yourtractorisequipped with an operatorpresence sensing
switch When engine is running, any attempt by the
operator to ieave the seat without first setting the parking
brake wi!i shut off the engine.
« Depress clutch/brake peda! into full “BRAKE” position

and hold.

" Place parking brake lever in "ENGAGED" position and

release pressure from clutch/brake pedal. Pedal should
remain in “BRAKE" position. Make sure parking brake

will hold tractor secure.

STOPPING (See Fig. 8)

MOWER BLADES -
" Move attachment clutch switch to "DISENGAGED”

position.

GROUND DRIVE ^
« Depress clutch/brake pedal into full “BRAKE" position.
» Move motion control lever to neutral (N) position.
IMPORTANT: THE MOTION CONTROL LEVER DOES
NOT RETURN TO NEUTRAL (N) POSITION WHEN THE

CLUTCH/BRAKE PEDAL IS DEPRESSED

ENGINE-

* Move throttle control to slow (-^) position.
NOTE: Failure to move throttle control to slow (•»)
position and allowing engine to idle before stopping may
cause engine to "backfire”.
■= Turn ignition key to "OFF" position and remove key.

Always remove key when leaving tractor to prevent

unauthorized use..

“ Never use choke to stop engine.

NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may

cause "browning" of grass. To eliminate this possibility,
always stop engine when stopping tractor on grass areas.

CAUTION: Always stop tractor com­
pletely, as described above, before leav­
ing the operator's position; to empty

grass catcher, etc.

TO USE THROTTLE CONTROL (See Fig. 8)

Always operate engine at full throttle.
• Operating engine at less than full throttle reduces the

battery charging rate

^ Full throttle offers the best bagging and mower perfor­

mance

TO USE CHOKE CONTROL (See Fig. 8)

Use choke control whenever you are starting a cold engine.
Do not use to start a warm engine,

" To engage choke control, pull knob out Slowly push

knob in to disengage.

TO MOVE FORWARD AND BACKWARD (See

Fig. 8)

The direction and speed of movement is controlled by the
motion control lever.
" Start tractor with motion control lever in neutral (N)

position.

0

Release parking brake and clutch/brake pedal,

o Slowly move motion control lever to desired position.

TO ADJUST MOWER CUTTING HEIGHT

(See Fig. 8)

The cutting height is controlled by turning the height adjust­
ment knob in desired direction.
» Turn knob clockwise (r^) to raise cutting height,
«- Turn knob counterclockwise to lower cutting

height.

The cutting height range is approximately 1-1/2“ to 4". The
heights are measured from the ground to the blade tip with
the engine not running. These heights are approximate
and ,may vary depending upon soil conditions, height of
grass and types of grass being mowed.
" The average lawn should be cut to approximately 2-1/2

inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth,

' For best cutting performance, grass over 6 inches in

height should be mowed twice. Make the first cut

relatively high; the second to desired height..

TO ADJUST GAUGE WHEELS (See Fig. 9)

Adjust gauge wheels with tractor on a flat level surface.
■> Adjust mower to desired cutting height (See ‘TO AD­

JUST MOWER CUTTING HEIGHT' in the Operation
section of this manual).

13