Toa SR-TB4WP - Manual

5
2
Turn the bracket base
upside-down to face the
speaker toward the right.
Speaker mounting bracket
(component of the SR-TB4WP)
Screws removed
in Step 3 (M5 x 20)
Waterproof washer
Pad
Note
Take care not to remove the
pad at speaker mounting.
Remove the 8 attached screws.
(The removed screws are used
in Step 4.) 3
Speaker
[When facing the speaker
toward the left]
Bracket base
(component of the SR-TB4WP)
Hexagon head bolt M8 x 20
(supplied with the SR-TB4WP)
1
180
ø60
90 4-12 x 22
[Wall mounting dimensions]
Bolts and nuts used to fix a bracket
base on a wall are not included. Use
bolts and nuts that are appropriate for
the construction of wall.
WARNING
Unit: mm
INSTALLATION MANUAL
WALL TILT BRACKET SR-TB4WP
The SR-TB4WP is designed to be used exclusively to mount the
SR-S4LWP or SR-S4SWP Line Array Speaker on a wall. It allows
the speaker orientation angle to be adjusted to 0° or 5° vertically
and 20° max. horizontally.
In Combination with the optional SP-131 Speaker Mount Bracket
and YS-60B Pole Band, the SR-TB4WP also permits the speaker
to be mounted on an outdoor pole.
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the
instructions in this section for correct and safe operation.
• Be sure to follow all the precautionary instructions in this section,
which contain important warnings and/or cautions regarding
safety.
• After reading, keep this manual handy for future reference.
3. SPECIFICATIONS
• Accessories
Hexagon head bolt M8 x 20 ............................... 4
• Optional products
Speaker mount bracket: SP-131
Pole band:
YS-60B
Note: The design and specifications are subject to change without
notice for improvement.
Step 1. Install the bracket base on a wall.
Determine the orientation of the bracket base
depending on whether the speaker is to face left or
right.
Step 2. Attach the speaker mounting bracket to the bracket
base.
Horizontal facing angle can be adjusted in the range of
0° to 20°.
2. INSTALLATION
Bracket base
Speaker mounting bracket
Horizontal facing angle: 20°
After the speaker's horizontal orientation has been
determined, fix the speaker mounting bracket to the base.
Note
The speaker's horizontal orientation can be adjusted after
the speaker has been installed.
Step 3. Remove the attached screws (with waterproof
washers) on both sides of the speaker.
Step 4. Connect a speaker cable to the speaker.
Step 5. Mount the speaker to the speaker mounting bracket.
The vertical facing angle toward down can be adjusted
either 0° (horizontal) or 5° by the selection of the
screw mounting holes.
Vertical facing
angle: 5° Vertical facing angle:
0° (horizontal)
• Refer all installation work to the dealer from whom the unit was
purchased. Installation requires extensive technical knowledge
and experience. The speaker may fall off if incorrectly installed,
resulting in possible personal injury.
• Install the unit only in a location that can structurally support the
weight of the unit and the speaker. Doing otherwise may result in
the speaker falling down and causing personal injury and/or
property damage.
• Owing to the speaker's size and weight, be sure that at least two
persons are available to install the speaker. Failure to do so
could result in personal injury.
• Do not use other methods than specified to mount the bracket.
Extreme force is applied to the unit and the speaker could fall off,
possibly resulting in personal injuries.
• Use nuts and bolts that are appropriate for the wall's structure
and composition. Failure to do so may cause the speaker to fall,
resulting in material damage and possible personal injury.
• Tighten each nut and bolt securely. Ensure that the bracket has
no loose joints after installation to prevent accidents that could
result in personal injury.
• Do not mount the unit in locations exposed to constant vibration.
The mounting bracket can be damaged by excessive vibration,
potentially causing the speaker to fall, which could result in
personal injury.
Indicates a potentially hazardous situation which, if mishandled,
could result in death or serious personal injury.
WARNING
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
CAUTION
• Avoid touching the unit's sharp metal edge to prevent injury.
• Do not stand or sit on, nor hang down from the unit as this may
cause it to fall down or drop, resulting in personal injury and/or
property damage.
• Have the unit checked periodically by the shop from where it was
purchased. Failure to do so may result in corrosion or damage to
the unit that could cause the unit to fall, possibly causing
personal injury.
Number of Speakers 1
to be Mounted
Finish Stainless
steel (SUS304)
Dimensions 167 (w) x 247 (h) x 201 (d) mm
(complete assembly)
Weight 2.8 kg (including accessories)
Product Composition Speaker mounting bracket ...... 1,
Bracket base ...... 1
133-01-442-8A
URL: http://www.toa.jp/
2.1. Munting on a Wall
1
Speaker mounting bracket
(component of the SR-TB4WP)
2
Bracket base (component
of the SR-TB4WP)
YS-60B Pole Band
(optional)
SP-131 Speaker Mount Bracket
(optional)
Washer*, Nut*
Bolt*
Pole
* Supplied with the SP-131.
[Example of pole mounted application]
The subsequent procedures follow Step2 or later in the
section "2.1. Mounting on a Wall."
The optional SP-131 Speaker Mount Bracket and YS-60B Pole
Band are required to mount the speaker on a pole.
Step 1. Attach the SP-131 to the bracket base using bolts,
washers and nuts supplied with the SP-131.
Determine the orientation of the bracket base in
advance depending on whether the speaker is to face
left or right.
Step 2. Install the SP-131 on a pole using the YS-60B.
The allowable pole diameter is 90 – 340 mm.
For the detailed mounting procedures of the SP-131
and YS-60B, see the instruction manual enclosed with
the SP-131.
2.2. Munting on a Pole