Toa SR-TB3 - Manual

INSTALLATION MANUAL
WALL TILT BRACKET SR-TB3
The SR-TB3 is a Wall Tilt Bracket designed to install the Line Array
Speaker SR-H2L, SR-H2S, SR-H3L or SR-H3S vertically on a wall.
It allows the speaker direction angle to be adjusted in the range of
0° to 5° downward and 0° to 15° leftward or rightward.
2. SPECIFICATIONS
Note: The design and specifications are subject to change without
notice for improvement.
Note: Only 1 speaker can be installed using the SR-TB3.
Step 1. Assemble the Bracket base, then install it on a wall.
1-1. Attach the Brackets A and B loosely to the Joint bracket to
make up a bracket base.
Determine Bracket A and B mounting positions (top or
bottom) depending on which the speaker is to face left or
right.
Note
The figure below shows an example when facing the
speaker rightward. Change the mounting positions of the
Brackets A and B with each other when facing the speaker
leftward.
Hex bolt M6 x 16
(supplied with the SR-TB3)
Bracket A
Note: Fix the bolts loosely.
Bracket A
Joint bracket
Bracket B
Wall
Note: Overhead view of the speaker
Joint bracket
Horizontal angle: 15°
Speaker
1-2. Install the Bracket base on a wall.
1-3. Determine the speaker's horizontal angle by adjusting the
angle of Joint bracket.
Horizontal angle can be adjusted from 0° to 15°. After the
speaker's horizontal direction has been determined,
securely tighten 4 bolts loosely fitted in Step 1-1.
Step 2. Attach the Speaker mounting bracket to the speaker's
rear surface.
2-1. Remove the specified screws on the speaker's rear
surface, then use their screw holes to secure the Speaker
mounting. In this event, the removed screws are not used.
Unit: mm (inches)
4-ш7
(4-ш0.28)
40 (1.57)
278 (10.94)
WARNING
Bracket
Bracket
Joint bracket
Bolts and nuts used to fix a
bracket base on a wall are
not included.
Use bolts and nuts that are
appropriate for the wall
material and structure.
Bracket base wall mounting dimensions
Speaker mounting bracket mounting position
[SR-H2L]
Speaker mounting
bracket
Hex bolt M5 x 25
(supplied with the SR-TB3)
Note
Remove the attached screws.
The removed screws are not used.
[SR-H2S] [SR-H3L] [SR-H3S]
502.2 (19.78)
422.2 (16.62)
718.2 (28.28) 680.2 (26.78)
Unit: mm (inches)
Speaker mounting bracket
Speaker mounting bracket
About 5 – 7 mm (0.2" – 0.3")
Hex bolt M6 x 16
(supplied with the SR-TB3)
Fix the hex bolts leaving about 5 – 7 mm
(0.2" – 0.3") protruding.
Speaker (rear)
Step 3. Install the speaker body to the Joint bracket.
3-1. Insert the hex bolts loosely fitted to the Speaker mounting
bracket into the Joint bracket's slots.
3-2. Fix the Speaker mounting bracket to the Joint bracket
loosely with the 4 supplied hex bolts.
Step 4. Connect the speaker cable to the removable terminal
plug.
For connection, refer to the instruction manual enclosed
with the speaker.
Step 5. Adjust the downward angle by moving the speaker
body.
Downward angle can be adjusted from 0° to 5°.
After the speaker's vertical direction has been determined,
securely tighten 6 bolts loosely fitted into the Speaker
mounting bracket.
Joint bracket
Insert into the Joint
bracket's slots.
Speaker mounting bracket
Removable terminal plug
3 -2
4
3 -1
Hex bolt M6 x 16
(supplied with the SR-TB3)
Speaker
Joint bracket
Speaker mounting
bracket
Hex bolt
0° to 5° 0° to 5°
These screws (one each on both sides)
serve as fulcrums, on which speaker
downward angle can be adjusted.
2-2. Fix 2 hex bolts (one each) loosely in the
center bolt-holes on both sides of the
Speaker mounting bracket.
133-05-446-40
URL: http://www.toa.jp/
1. SAFETY PRECAUTIONS
3. INSTALLATION
• Before installation or use, be sure to carefully read all the
instructions in this section for correct and safe operation.
• Be sure to follow all the precautionary instructions in this section,
which contain important warnings and/or cautions regarding
safety.
• After reading, keep this manual handy for future reference.
• Install the unit only in a location that can structurally support the
weight of the unit and the speaker. Doing otherwise may result in
the unit falling down and causing personal injury and/or property
damage.
• Since the unit is designed for in-door use, do not install it
outdoors. If installed outdoors, the aging of parts causes the unit
to fall off, resulting in personal injury.
• Do not use other methods than specified to mount the bracket.
Extreme force is applied to the unit and the unit could fall off,
possibly resulting in personal injuries.
• Use nuts and bolts that are appropriate for the wall material and
structure. Failure to do so may cause the speaker to fall, resulting
in material damage and possible personal injury.
• Tighten each nut and bolt securely. Ensure that the bracket has
no loose joints after installation to prevent accidents that could
result in personal injury.
• Use the specified speaker in combination. Doing otherwise may
cause the unit or component to fall off, resulting in personal injury.
• Do not mount the unit in locations exposed to constant vibration.
The mounting bracket can be damaged by excessive vibration,
potentially causing the unit to fall, which could result in personal
injury.
• Avoid touching the unit's sharp metal edge to prevent injury.
• Do not stand or sit on, nor hang down from the unit as this may
cause it to fall down or drop, resulting in personal injury and/or
property damage.
• Have the unit checked periodically by the shop from where it was
purchased. Failure to do so may result in corrosion or damage to
the unit or speaker that could cause the unit to fall, possibly
causing personal injury.
WARNING
Indicates a potentially hazardous situation which, if
mishandled, could result in death or serious personal injury.
CAUTION
Indicates a potentially hazardous situation which, if
mishandled, could result in moderate or minor personal injury,
and/or property damage.
Applicable Speaker SR-H2L, SR-H2S, SR-H3L, SR-H3S
Finish Rolled steel plate, white, paint
Dimensions 64 (w) x 296 (h) x 50 (d) mm
(2.52" x 11.65" x 1.97")
Weight 1.4 kg (3.09 lb)
Component Speaker mounting bracket ............. 1,
Bracket A ........... 1, Bracket B ...... 1,
Joint bracket ...... 1
Accessories Hex bolt M5 x 25 (with washer) .......... 4
Hex bolt M6 x 16 (with washer) ........ 10