Installation, Electrical power requirements, Setting up – Sonics GXT User Manual
Page 10
I N S T A L L A T I O N
ELECTRICAL POWER REQUIREMENTS
The power supply requires a fused, single-phase, standard 3-terminal
grounding type receptacle capable of supplying the requisite voltage and
current. Refer to the table below for power specification.
SETTING UP
The power supply is a free-standing assembly. It should be installed in a
clear, uncluttered location that is free from excessive dirt, dust, corrosive
fumes, and temperature and humidity extremes. The selected installation site
should be near the electrical power source and away from equipment that
generates abnormally high electrical transients. Observe the following
additional instructions when installing the equipment:
a. Allow at least 6 inches (152.4mm) at the rear of the power supply for cable
connections.
b. Position the power supply so that the front panel controls are visible and
readily accessible.
c. The power supply is air cooled; allow sufficient space around the
assembly to ensure adequate ventilation. If the power supply must be
housed in a confined space, forced air cooling may be necessary to keep
surrounding air within acceptable ambient temperature limits. Periodically
check the ventilation grille and clean as necessary.
¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥
¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥
I N S T R U C T I O N M A N U A L • M O D E L G X T P O W E R S U P P LY
9
The line cord of the
controller/power supply
is equipped with a 3-
prong, grounding plug.
Do not, under any
circumstances, remove
the ground prong. The
plug must be plugged
into a mating 3-prong,
grounding type outlet.
POWER SPECIFICATIONS
NOTE: If power supply
is to be run
continuously, air cooling
of the converter and
horn is required. Use
clean, dry compressed
air filtered down to 5
microns (supplied to
converter fitting – see
Power Rating/
Model
Frequency
115 vac
230 vac
GXT400-40
400w - 40 kHz
15 amps
10 amps
GXT800-40
800w - 40 kHz
15 amps
10 amps
GXT1200-20
1200w - 20 kHz
15 amps
10 amps
GXT1700-20
1700w - 20 kHz
N/A
20 amps
GXT2200-20
2200w - 20 kHz
N/A
20 ampT
GXT3500-20
3500w - 20 kHz
N/A
30 ampT
GXT2200-15
2200w - 15 kHz
N/A
20 amps
GXT3500-15
3500w - 15 kHz
N/A
30 amps
GXT4500-15
4500w - 15 kHz
N/A
30 amps
Fuse rating