Philips CDI210/73 - Manual (Page 11)

PLAYING DISCS
GENERAL
Push button control;
• For basic play control, or for playing discs through a stereo
system without using the TV, you can use the buttons on the
front panel or on the remote control.
- The PLAY and STOP buttons operate in the same way as the
corresponding on-screen functions.
- The NEXT and PREVIOUS buttons skip one track forward or
bacltward respectively.
NOTE
- The functioning of these buttons will depend completely on
the application when playing a CD-i program.
Changing over to TV:
• Select the desired channel or input of your TV using the
controls of your TV set.
- When the player is switched on, its antenna signal is fed
through to the TV and depending on the player-TV
connection, TV reception might be interrupted automatically.
• To change over to TV reception at any time in such case,
press the CD-i/TV button (11) on the remote control
• To return to CD-i play, press the CD-i/TV button (7/) again.
Sound leveL
• When playing any disc adjust the sound level as required,
preferably on the TV or HiFi amplifier.
• The volume up (9)/dovm (10) buttons on the remote control
may also be used, but for each disc these controls always start
at the level set in the General Options Screens.
A suitable level must therefore first be set on the TV or HiFi
amplifier.
LOADING AND UNLOADING
Loading;
• Point and click on 'Open'
(you may also press the
OPEN /CLOSE button (2) on
the player) to open the disc
tray (1).
• Take the disc from its holder
and place it on the tray with
the label up.
• Point and click on 'Close' (you
may also press the
OPEN/CLOSE button (2) on
the player, or gently push the
front of the tray) to close the
tray.
- The TV screen changes according to the type of disc.
Unloading:
• Point and click on 'Open' (you may also press the
OPEN /CLOSE button (2) to open the disc loading tray.
— The player start-up screen reappears on the TV.
• Take the disc from the tray and replace it in its holder.
• Point and click on 'Close' (you may also press the
OPEN/CLOSE button (2) on the player, or gently press the
front of the tray) to close the tray with or without a new disc.
NOTE
— You may unload the disc at any time by pressing the
OPEN/CLOSE button (2).
— Unloading a CD-i disc while the CD-i program is running, will
terminate the CD-i program abruptly. 'Bookmarks' or
intermediate results, if used by the CD-i program, might not
be updated to the latest situation.
CAUnON
NEVER POT MORE THAN ONE DISC AT A TIME INTO THE
CD-i PLAYER
PLAYING A CD-i DISC
Playing a CD-i disc depends on the value of Autoplay (see
Options Screens). The factory setting is default "OFF".
1. When autoplay is "OFF":
After the disc is loaded, the CD-i start-up screen appears on the
TV. To start the CD-i program, select 'Play' and click on it.
2. When autoplay is "ON":
After the disc is loaded, the CD-i program will start up
automatically.
The opening screen of the CD-i
program now appears on the TV.
From this point, all interaction is
between you and the program.
To stop at any time, select the
STOP or EXIT function provided
by the CD-i program.
NOTE
- This procedure applies equally to CD BRIDGE discs, CD-i
READY discs and PHOTO CDs. And for Digital Video discs
and Video CD's when a Digital Video Cartridge has been
installed.
CAUTION
NEVER LEAVE A STILL PICTURE ON THE SCREEN FOR ANY
UENGTH OF TIME. THIS CAN CAUSE BURNING-IN OF THE
PICTURE TUBE. TO AVOID THIS SWITCH OFF THE PLAYER
OR REMOVE THE DISC.
11