Great Planes T-Craft 20 Kit - GPMA0155 - Manual (Page 4)

4
These are the building supplies that are required. We
recommended Great Planes Pro ™ CA and Epoxy glue.
❏ 1 oz. Thin Pro CA (GPMR6002)
❏
1 oz. Medium Pro CA (GPMR6008)
❏
6-Minute Pro Epoxy (GPMR6045)
❏ 30-Minute Pro Epoxy (GPMR6047)
❏ Thread locking compound (GPMR6060)
❏
Balsa filler (HCAR3401)
❏
Canopy Glue
❏ Plan protector (GPMR6167)
❏
Isopropyl rubbing alcohol (70%)
❏
Paper towels
❏
Sanding block and sandpaper (coarse, medium, fine)
❏
Hobby knife (HCAR0105)
❏ #11 blades (HCAR0211)
❏
Single-edge razor blades (HCAR0212)
❏
Razor saw
❏ Razor plane (MASR1510)
❏ Electric drill
❏
Drill bits - 1/16",3/32", 5/32", 3/16", 13/64", 7/32”, 1/4"
❏
Small Phillips and flat blade screwdrivers
❏ Pliers with wire cutter (HCAR0630)
❏
Sealing Iron (TOPR2100)
❏
Heat gun (TOPR2000)
❏ T-Pins (HCAR5150)
❏
Straightedge with scale (HCAR0475)
❏
Cutting mat (HCAR0456)
❏
Builder's triangle (HCAR0480)
❏ 1/4-20 Tap and Drill set (GPMR8105, drill bit included)
❏
Tap handle (GPMR8120)
❏
Masking Tape (TOPR8018)
❏ Monofilament string for aligning the wing and stabilizer
❏
Panel line pen (TOPQ2510)
❏
Groove Tube (GPMR8140)
❏ Dead Center Hole Locator (GPMR8130)
❏ Precision Hinge Marking Tool (GPMR4005)
❏
Microballoons (TOPR1090)
❏
CG Machine ™ (GPMR2400)
❏ Accu Throw ® Deflection Meter (GPMR2405)
❏
CA Applicator tips (HCAR3780)
❏
CA Debonder (GPMR6039)
❏ Clevis installation tool (GPMR8030)
❏ Hot Sock ™ (TOPR2175)
❏
Curved-Tip canopy scissors (HCAR0667)
❏
Top Flite Precision Magnetic Prop Balancer ™ (TOPQ5700)
❏ Slot Machine ™ motorized hinge slotting tool (GPMR4010)
On our workbench, we have three 11" Great Planes Easy-
Touch
™ Bar Sanders, equipped with #80, #150 and #220-
grit sandpaper. This setup is all that is required for almost
any sanding task. We also keep some #320-grit wet-or-dry
sandpaper handy for finish sanding before covering.
Great Planes Easy-Touch Bar Sanders are made from
lightweight extruded aluminum and can be found at most
hobby shops. They are available in five sizes – 5-1/2"
(GPMR6169) for those tight, hard-to-reach spots; 11"
(GPMR6170) for most general purpose sanding; and 22"
(GPMR6172), 33" (GPMR6174) and 44" (GPMR6176) for
long surfaces such as wing leading edges. The Easy-
Touch Adhesive-Backed Sandpaper comes in 2" x 12'
rolls of 80-grit (GPMR6180), 150-grit (GPMR6183) and
220-grit (GPMR6185) and an assortment of 5-1/2" long
strips (GPMR6189) for the short bar sander. The adhesive-
backed sandpaper is easy to apply and remove from your
sanding bar when it's time for replacement.
This setup is all that is required for almost any sanding task.
Custom sanding blocks can be made from balsa or hardwood
blocks and dowels for sanding difficult-to-reach spots.
Fuse = Fuselage
LE = Leading Edge (front)
TE = Trailing Edge (rear)
Stab = Stabilizer
" = Inches
Elev = Elevator
LG = Landing Gear
Ply = Plywood
Common Abbreviations
Optional Supplies and Tools
Tools
Building Supplies