Philips VR6293 - Manual (Page 19)

• P ress + o r - a s m an y tim es as n ecessary to select th e
co rrect d ate o n w h ich th e first reco rd in g h as to be m ad e.
T o repeat reco rd in g every w eek on the sam e day an d at th e
sam e tim e:
• P ress X o ne o r m o re tim es u ntil th e D isp lay sho w s:
• P ress + o r - a s m an y tim es as n ecessary to select th e
co rrect d ate o n w h ich th e first reco rd in g h as to be m ad e.
( 9 ) Press 9 (9 again.
The Display shows, for example;
nnni.
n^uu.
"I
I
@ Press + or - or the digit buttons (0-9) on the remote control
to select the correct TV station to be recorded.
Note:
- if TIMER-Block 4 is selected, on the display appears
"PAGE—".Fiii the correct TXT-Subtitel page number
(3*position) in. Push X if this TIMER-block shell be
programmed without TXT-subtitle,
(1J) Press ® ❖ >) once more.
For 5 seconds the Display shows,for confirmation (example):
T
1
IT/CO
1 1 MI_K
'"I
l_
i?T^T 3 ?l
00 00
»i.'iTsn is shown on the Display as well.
@ Press 16 to switch the video recorder to standby.
Important notes:
- A timed recording wilt only be made if the video recorder is
in standby at the start time. If necessary press l to select
standby.
If the timed recording starts, the timer will automatically switch
on the video recorder.
- If a cassette is not loaded in the video recorder after
programming a timed recording the Display shows ‘CASS’.
- If a protected cassette is loaded after programming a
timed recording ‘PROT’ flashes on the Display for 5 seconds.
The cassette will be ejected.
- Before a timed recording starts you can use the video
recorder normally.
If you continue to use the video recorder after the start time of
a timed recording, your timed recording, will not be carried out,
CCan then flashes on the Display.
You can then still start the timed recording by pressinglÒ
once.
QESIil will stop flashing.
- During a timed recording, you cannot use the video
recorder. You may, however, cancel the timed recording by
pressinglÒ.
- When the tape reaches the end during a timed recording,
the cassette will be ejected auomatically and the video
recorder switches itself to standby.
“ If you want to re-use the previously stored information of a
TIMER block, you only have to re-program the date by pressing
+ or-.
If TIMER-block 4 is programmed with a wrong TXT-subtitle
page number, the symbol S appeas in the upper left corner
of the recording.
Programming a timed recording on the remote control
(without teletext)
You can program timed recordings on the remote control using
( 9RC) 3nd the digit buttons (0-9) and then transmit the
programming details to the video recorder using (¡((O).
On the Display of the remote control all the programming steps will
be shown.
The contents of all "TIMER" blocks will be stored in the remote
control.
Note:
If d u ring prog ram m in g a b utto n is n ot pressed w ith in 1 m in ute,
yo u h ave to start th e prog ram m in g seq uence fro m the
b eg in n in g again .
0 Press (® RC) to recall the last programmed recording details.
The Display shows for example:
- TIM ER -1 V » « • • • V
~ TRANSM IT-
' ' l l
1
1 »
START m .1
ir
DATE o n
I L _ l U i
L-
STO P l O
r n PRO G in
I I ' U U l U
(®) 15