Philips VR6293 - Manual (Page 17)

Note:
If the selected TV station has 'TOP-"or"FASTEXT"or
"FLOF-system", you can also use the coloured TXT buttons
( B ) on the remote control.
(7) Press (9
A cursor (indication point) appears on the TV programme page.
At the information line (on top of the TXT page) it is indicated if
"VPT-" or "TEXT-PROGRAMMING" is possible (depending on
the responsible TXT-broadcaster).
"TEXT-PROGRAMMING" means that not all data can be used
automatically by the videorecorder. Some data may have to be
corrected manually.
The TV screen shows for example:
TEXT-PROGRAMMING
222 ORF-TEIETEXT 19.01. 16:03
TV-PROGRAM ___
ORF
HEUIE
f S2
19.61 i NACHRICHTEN
20.15 LOKAL PROGRAMM
21.00 AUSLANDSREPORT
22.30 WERBUNG
22.45 EISKUNSTLAUF-EUROPAMEISTER
KOr der Herrn
23.45 CLUB 2 (siehe 227)
SEUCT PROG WITH
*!■ ,
COKnRM WITH 9
CURSOR
• Press + (down) or - (up) to move the cursor to the start time of
the desired TV programme.
Note:
If all TIMER-block are occupied, you are requested to
cancel at least one TIMER block and the TV screen
shows for example:
12JAHUARn989 13.45
TIMER START END DATE PRDG
1 1 20.15 21.15 15 1
2 18.00 18.30 19 2
3 17.20 19.45 27 4
4 0.20 9.15 5 7
AU TIMERS OCCUPIED.
If you don’t want to cancel the occupied TIMER-blocks:
• Press ( @ ).
The previously displayed TXT page will be shown again,
the TXT programming mode is cancelled.
If you want to cancel an occupied TIMER-block and program it
again:
•
Press + or - or digit button (0-9) to select the TIMER.block
you want to cancel.
• Press X on the remote control.
• Press (9^ )
The TV programme page will page will be shown again
on the TV screen, but now including a cursor,
• Press + or - to select the desired TV programme.
(g) Press (®<0^) again.
The TV screen shows for example:
22.40 EISIA U F-EU RO PA M B STER
K urderH em i
23.45 CLU B 2 (siehe 227)
START END DATE PROG
1=1 = =1 =□
20.15 21.15 19 i
C H ECK PRO SR A M M N U M B ER.
PR ESS "O SO '-B U nO N FO R H ELP-M EN U
if you want to change the start time, the stop time, the date or the
preselection number:
• Press the coloured button ( B ) on the remote control which
corresponds to the colour of what you want to change on the TV
screen.
• Use + or - or the digit buttons (0-9) to change the data.
Note:
If you use the digit buttons (0-9), the date and the
preselection number have to be entered in a two-digit form,
e.g, "Or for preselection number 1.
• Press (O) on the remote control to get additional help
information on the screen.
(9) Press (®
The TV screen shows a summary of all programmed TIMER-
blocks.
Note;
You can recall this TIMER summary at any time, also if TXT is
not selected by pressing OSD button (¡3).
To switch off the TIMER summary, press (Q) again.
if you want to continue to programming a new block starting from
step0, press (®^).
• If you want to interrupt programming, press TXT button ((M)).
• If you want to return to live TV picture, press (B) again.
General notes;
- During programming with TXT, playback and wind
functions are impossible.
-
If you press i(i) during programming with TXT,
the videorecorder will be switched off without changing
any data
- During the firstVPT-programming procedure, the video
recorder requests to check the preselection number to be
recorded.
Following example illustrates how the automatic "TV station
recognition" works:
-Preselection number ”1" is stored for”ZDF"
-Preselection number "2" is stored for "ARD"
-Preselection number "3" is stored for "8R"
• Ail these 3 TV stations have the same TXT-system and
each TV station shows all 3 programm summaries.
• Preselection number "1/ZDF" is selected on the VCR.
• You want to program a timed recording from "2/ARD" by
VPT-programming.
Choose the desired TV programme - the VCR asks to
check the preselection number,
• Select "2" for "ARD" and press (B) to confirm the
preselection number. Finalize the programming sequence
following steps;9)and The preselection number ”2"
is now assigned to the TV station ’ARD".
( gb ) 13