Commands – overview – Flintec LDU 68.2 User Manual
Page 12
LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010
Page 12 of 28
7.
Commands – Overview
Command Short
description
Parameter
value
Page
AD
Communication: Device Address
0...255
23
A0/A1
Setpoints: Output of Gros Value (0) or Net Value(1)
0 or 1
22
BR
Communication: Baud Rate
9600…115200 baud 23
CE
Calibration: Open Calibration Sequence; Read TAC Counter
0...65535
14
CI
Calibration: Minimum Output Value
–99999...0 d
14
CG
Calibration: Set Calibration Gain (Span) at Load > Zero
0...99999
15
CL
Communication: Close Device
None
23
CM
Calibration: Set Maximum Output Value
1...99999 d
14
CS
Save the Calibration Data (CM, CI, DS, DP, CZ, CG, etc.) to EEPROM
None
15, 24
CZ
Calibration: Set Calibration Zero Point – scale without load
None
14
DP
Calibration: Set Decimal Point Position
0...5
14
DS
Calibration: Set Display Step Size
1, 2, 5, 10…, 200
14
DX
Communication: Set Half-duplex (0) or Full-duplex (1)
0 or 1
23
FD
Factory default settings: Write data to EEPROM (TAC protected)
None
15
FF
Digital filter: Moving Average
0…15
17
FL
Digital filter: Filter Cut-off Frequency
0...7
17
GA
Trigger function: Get Average Value
None
25
GF
Output: Get Filtered Value
None
19
GG
Output: Get Gross Value
None
19
GI
Saves an image file from the LDU’s EEPROM
None
24
GN
Output: Get Net Value
None
19
GS
Output: Get ADC Sample Value
None
19
GT
Output: Get Tare Value
None
19
GW
Output: Get Data String “Net/Gross/Status“
None
19
H0/H1
Setpoints: Hysteresis for Setpoint S0 (H0) or S1 (H1)
-99999...+99999 d
22
ID
Device information: Identify Device
None
13
IM
Digital output: Enable Output for External Control
0000...0011
21
IN
Digital input: Input Status
None
21
IO
Digital output: Output Status
0000...0011
21
IS
Device information: Identify Device Status
None
13
IV
Device information: Identify Firmware Version
None
13
MT
Trigger function: Measuring Time for Averaging
0...500 ms
25
NR
Motion detection: No-motion Range
0...65535 d
16
NT
Motion detection: No-motion Time Period
0...65535 ms
16
OP
Communication: Open Device xxx
0...255
23
PI
Download a saved image file to the LDU’s EEPROM
None
24
RS
Device information: Read serial number
None
13
RT
Scale function: Reset Tare and Switch to Gross Indication
None
18
RZ
Scale function: Reset Zero Point
None
18
SA
Auto-transmit: Send Triggered Average Value automatically
None
20, 25
SD
Trigger function: Start Delay
0...500 ms
25
SF
Auto-transmit: Send Filtered Net Value continuously (Display Mode only) None
20
SG
Auto-transmit: Send Gross Value continuously
None
20
SN
Auto-transmit: Send Net Value continuously
None
20
S0/S1
Setpoints: Setup of Setpoints S0 and S1
-99999...+99999 d
22
SR
Reset Firmware (Warm Start)
None
13
SS
Save Setpoint Data (S0, S1, H0, H1, A0 and A1) to EEPROM
None
24
ST
Scale function: Set Tare and Switch to Net Indication
None
18
SW
Auto-transmit: Send Data String „Net/Gross/Status“ continuously
None
20
SZ
Scale function: Set Zero
None
18
TD
Communication: Transmission delay
0…255 ms
23
TE
Trigger function: Trigger on Rising Edge (1) or Falling Edge (0)
0 or 1
25
TL
Trigger function: Trigger Level
0...99999 d
26
TR
Trigger function: Software Trigger
None
25
UR
Digital filter: Update Rate
0...2
17
WP
Save the Setup Data (FL, NR, NT, AD, BR, DX) to EEPROM
None
24
ZI
Calibration: Initial Zero Range
0...99999 d
15
ZT
Zero Tracking: Disable (0) or Enable (1)
0 or 1
15