Kenmore 146.1615311 - Manual (Page 8)

1
«
Turn cor
in use.
trols and gas source or tank OFF when not
1 / »
L *
CAUTION
1
/ ! \:
If ignitio
burner c
lighting
The valv
burner a
n does NOT occur in 5 seconds, turn
ontrols OFF, wait 5 minutes and repe
orocedure. If the burner does not ign
e open, gas will contiune to flow out
nd could accidently ignite with risk o
the
at the
te with
of the
f injury
Match-Lighting
AD o not lean over grill while lighting.
1. Open lid during lighting.
2. Place match into match holder (hanging from side of carf).
Lighf mafch, place info lighfing hole on leff side of firebox.
3. Push in and furn righf knob to Hi position. Be sure burner lights
and stay lit.
4. Light other burners follow with steps 3.
Sideburner Ignitor Lighting
AD o not lean over grill while lighting.
l.Open lid for side burner during lighting.
2.
Turn on valve from source or tank.
3. Push and turn Side Burner control knob to ^^Hl and
immediately press and hold Electronic Ignition button.
4. If ignition does NOT occur in 5 seconds, turn Side Burner
control knob OFF, wait 5 minutes, and repeat the lighting
instructions.
Sideburner Match Lighting
l.Open sideburner lid. Turn on gas at LP cylinder.
2. Place lit match near burner.
3. Turn sideburner knob to HI. Be sure burner lights and stays lit.
........................... ...............—>c <
Burner Flame Check
• Remove cooking grates and flame tamers. Light burners, rotate
knobs from HIGH to LOW. You should see a smaller flame in
LOW position than seen on HIGH. Perform burner flame check
on sideburner, also. Always check flame prior to each use. If
only low flame is seen refer to "Sudden drop or low flame" in
the Troubleshooting Section.
^^***^^
Turning Grill Off
• Turn all knobs to OFF position. Turn LP cylinder off by turning
Ignitor Check
• Turn gas off at LP cylinder. Press and hold electronic ignitor
button. "Click" should be heard and spark seen each time
between collector box or burner and electrode. See
"Troubleshooting" if no click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before
checking valves. Knobs lock in OFF position. To check
valves, first push in knobs and release, knobs should spring
back. If knobs do not spring back, replace valve assembly
before using grill. Turn knobs to LOW position then turn back to
OFF position. Valves should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn.
Replace damaged hoses before using grill. Use only
valve/hose/regulator as specified in the parts list of this Use & Care
Guide.
General Grill Cleaning
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory (and should never be painted). Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry. Do not apply a caustic grill/oven cleaner to painted
surfaces.
• Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring powder
for stubborn stains.
• Painted surfaces: Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
n.onabrasive cloth.
• Stainless steel surfaces: To maintain your grill's high guality
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease
deposits may reguire the use of an abrasive plastic cleaning
pad. Use only in direction of brushed finish to avoid damage.
Do not use abrasive pad on areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.
8 • 16153- 50300312