Amir:l, Caution – Kenmore 415.1615111 User Manual
Page 8
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
A
A
Turn cor
in use.
itrols and gas source or tank OFF wf
sen
not
A
CAUTION
A
If ignitio
burnerc
lighting
the valv
burnerc
injury.
n does NOT occur in 5 seconds, turn
rontrols OFF, wait
5
minutes and
reps
procedure.
If
the burner does not igr
e open, gas will continue to flow out
ind could accidently ignite with risk
the
sat
the
life
with
of the
of
Match-Lighting
A
Do
not
lean over grill while lighting.
1. Open lid. Turn ON gas at LP cylinder.
2.
Place match into match holder (hanging from side panel
of
grill). Light match; then light burner by placing match
through the match light hole on right or left side of grill.
3. Push in and turn far right or far left burner knob to the HI
position, depending on match light hole selected. Be sure
burner lights and stays lit.
4. Light adjacent burners in sequence by pushing knobs in
and turning to the HI position.
Sideburner Ignitor Lighting
A Do not lean over grill while lighting.
1. Open sideburner lid. Turn ON gas at LP cylinder.
2. Turn sideburner knob to the HI position, push and hold
ELECTRONIC IGNITION button.
3. If sideburner does NOT light within
5
seconds, turn knob
to OFF, wait
5
minutes, then repeat lighting procedure.
Sideburner Match Lighting
1. Open sideburner lid. Turn ON gas
at LP cylinder.
2. Place lit match near burner.
3. Turn sideburner knob to the HI
position. Be sure burner lights and
stays lit.
Burner Flame Check
• Remove cooking grates and flame tamers. Light burners,
rotate knobs from HI to LOW. You should see a smaller
flame in LOW position than seen on HI. Perform burner
flame check on sideburner, also. Always check flame prior
to each use. If only low flame is seen refer to "Sudden
drop or low flame" in the Troubleshooting Section.
Amir:L
& & & & &
Turning Grill Off
• Turn all knobs to the OFF position. Turn LP cylinder OFF by
turning hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP cylinder. Press and hold electronic
ignitor button. "Click" should be heard and spark seen
each time between each collector box or burner and
electrode. See "Troubleshooting" if no click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before
checking valves. Knobs lock in OFF position. To check
valves, first push in knobs and release, knobs should spring
back. If knobs do not spring back, replace valve assembly
before using grill. Turn knobs to LOW position then turn
back to OFF position. Valves should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn.
Replace damaged hoses before using grill. Use only
identical replacement part valve/hose/regulator as
specified in the Parts List of this Use and Care Guide.
General Grill Cleaning
• Do not mistake brown or black accumulation of grease
and smoke for paint. Interiors of gas grills are not painted
at the factory (and should never be painted). Apply a
strong solution of detergent and water or use a grill
cleaner with scrub brush on insides of grill lid and bottom.
Rinse and allow to completely air dry. Do not apply a
caustic grill/oven cleaner to painted surfaces.
• Plastic parts: Wash with warm soapy water and wipe dry.
A
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to
and failure of parts can result.
• Porcelain surfaces: Because of glass-like composition,
most residue can be wiped away with baking soda/water
solution or specially formulated cleaner. Use nonabrasive
scouring powder for stubborn stains.
• Painted surfaces: Wash with mild detergent or
nonabrasive cleaner and warm soapy water. Wipe dry
with a soft nonabrasive cloth.
• Stainless steel surfaces: To maintain your grill’s high
quality appearance, wash with mild detergent and warm
soapy water and wipe dry with
a
soft cloth after each
use. Baked-on grease deposits may require the use of an
abrasive plastic cleaning pad. Use only in direction of
brushed finish to avoid damage. Do not use abrasive pad
on areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain
on cooking surfaces prior to grilling. It is not
recommended to clean cooking surfaces while grill is hot.
8 • 464220311