Fj-otions – Kenmore ELITE OASIS 110.6703 User Manual

Page 22

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

fj-otions

You can customize your cycles by selecting options.

ptions

■ Damp Dry Signal

AUTOiTCirS OMT

Wrinkle Guard 60

Damp Dry Signal

Select the Damp Dry Signal to alert you that your clothes are
approximately 80% dry or suitable for ironing. This is useful when

you want to remove lightweight items in a mixed load to avoid

overdrying or remove partially dry items that may need ironing.

The DAMP DRY SIGNAL is useful when drying bedsheets/linens

in a mixed load. When the signal goes off, open the door to stop

the dryer, rearrange the load inside the dryer, close the door and

restart the dryer to finish the drying cycle. Rearranging the load

will aid in the drying process.

NOTE:

The Damp Dry Signal is available only with the Auto Dry

Cycles.

WRINKLE GUARD® (30, 60,90,150 minutes)

WRINKLE GUARD® helps smooth out wrinkles that may form
when clothes are not removed promptly at the end of a cycle.

During this option, the dryer stops tumbling and then tumbles

again for a brief period without heat when pressed.

■

Press WRINKLE GUARD® to get heat-free, periodic tumbling
at the end of a cycle. WRINKLE GUARD® periodically starts
and stops the dryer, tumbling the load without heat for 30, 60,
90 or 150 minutes (depending on your model) unless you
open the dryer door.

■

Stop WRINKLE GUARD® at any time by pressing WRINKLE
GUARD®, opening the dryer door or pressing STOP.

■

For the Casual Cycle, WRINKLE GUARD® is preset to ON.

The other Auto Dry Cycles will retain the WRINKLE GUARD®

setting. Eor example, if you select WRINKLE GUARD® in the
Normal cycle, WRINKLE GUARD® will be on the next time you
select the Normal cycle.

NOTE:

If you do not select WRINKLE GUARD®, the dryer stops

after cool down.

Cycle Signal

The Cycle Signal produces an audible sound when the drying

cycle is finished. Promptly removing clothes at the end of the
cycle reduces wrinkling.

Press CYCLE SIGNAL to turn the Cycle Signal On or Off.

^ on

\g/

Off

Cycle Signal

NOTE:

When WRINKLE GUARD® is selected, a tone sounds

every 5 minutes until the clothes are removed, or WRINKLE
GUARD® ends.

You can change Auto and Timed Cycles, Modifiers and Options
anytime before pressing Start.

■ Three short tones sound if an unavailable combination is

selected. The last selection will not be accepted.

Changing Cycles after pressing Start

1. Press STOP twice.

Select the desired cycle and options.

Press START. The dryer starts at the beginning of the new

cycle.

NOTE:

If you do not press Start within 5 minutes of selecting the

cycle, the dryer automatically shuts off.

Changing Modifiers and Options after pressing Start

You can change a Modifier or Option anytime before the selected

Modifier or Option begins.

1. Press STOP once.

Select the new Modifier and/or Options.

Press START to continue the cycle.

NOTE:

If you happen to press STOP twice, the program clears

and your dryer shuts down. Restart the selection process.

Changing the Preset Dryness Level Settings

If all your loads on all Auto Dry cycles are consistently not as dry

as you would like, you may change the preset Dryness Level
settings to increase the dryness. This change will affect all of your

Auto Dry oycles.

Your Dryness Level settings can be adjusted to adapt to different

installations, environmental conditions or personal preference.

There are 3 drying settings: 1 (factory preset dryness level),

2 (slightly dryer clothes, approximately 15% more drying time)
and 3 (much dryer clothes, approximately 30% more drying

time).

1. The Dryness Level settings cannot be changed while the

dryer is running.

Press and hold the Dryness Level button for 5 seconds. The

dryer will beep, and “CF” will be displayed for 1 second

followed by the current drying setting.

To select a new drying setting, press the Dryness Level key

again until the desired drying setting is shown.

NOTE:

While cycling through the settings, the current setting

will not flash, but the other settings will flash.

Press START to save the drying setting.

The drying setting you selected will become your new preset

drying setting for all Auto Dry cycles.

This manual is related to the following products:

ELITE OASIS 110.6704