Kenmore ELITE OASIS 110.6703 - Manual (Page 19)

To make changes during an Auto Dry Cycle:
■ Press STOP.
■ Adjust Dryness Level.
NOTE; Dryness Level selections can be made only while
using Auto Dry Cycles.
More
' ■ Normal
Dryness
Level
cs ooirici. l.Op|. •SiSift,
To stop or pause your dryer at any time
Open the door or press STOP once. Press STOP twice to cancel
a cycle.
To restart the dryer
Close the door. Press START until dryer starts.
NOTE: Drying will continue from where the cycle was interrupted
if you close the door and press Start within 5 minutes. If the cycle
is interrupted for more than 5 minutes, the dryer will shut off.
Seleot new cycle settings before restarting the dryer.
Auto Dry Cycles take the guesswork out of drying time
and enhance fabric care. The amount of time that is
displayed is the estimated time remaining in the cycle.
To use a Timed Cycle
■ Select a Timed Cycle.
■ Press the TIME ADJUST (More Time or Less Time)
buttons until the desired drying time is displayed. Press
MORE TIME or LESS TIME once and the time will change
by 1-minute intervals. Press and hold MORE TIME or
LESS TIME and the time will change by 5-minute
intervals.
NOTE: The Time Adjust feature can be used only with
Timed Cycles.
Time Adjust
-ifSS
■ Press TEMPERATURE until the desired temperature
illuminates.
NOTE: During a Timed Cycle, you can change the settings for
Time, Temperature, WRINKLE GUARD® and Cycle Signal.
NOTE: The Temperature feature can be used only with
Timed Cycles.
(OPTIONAL STEP) If desired, select OPTIONS. For more
details, see “Options.”
(OPTIONAL STEP) If desired, press CYCLE SIGNAL. A signal
will sound to alert you when a cycle ends. For more details,
see “Cycle Signal.”
Press START. Be sure the door is closed.
■ If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically shuts off.
■ If you wish to end your drying cycle after pressing Start,
press STOP twice.
Select the correct cycle and dryness level or temperature for your
load. If an Auto Dry Cycle is running, the display shows the
estimated cycle time when your dryer is automatically sensing
the dryness level of your load. If a Timed Cycle is running, the
display shows the exact number of minutes remaining in the
cycle.
Cool Down tumbles the load without heat during the last few
minutes of all cycles. Cool Down makes the loads easier to
handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Drying tips
■ Follow care label directions when they are available.
■ If desired, add a fabric softener sheet. Follow package
instructions.
■ To reduce wrinkling, remove the load from the dryer as soon
as tumbling stops. This is especially important for permanent
press, knits and synthetic fabrics.
■ Avoid drying heavy work clothes together with lighter fabrics.
This could cause overdrying of lighter fabrics and lead to
increased shrinkage or wrinkling.
Cycle tips
■ Dry most loads using the preset cycle settings.
■ Refer to the Auto or Timed Preset Cycle Settings charts (in
the “Cycles” section) for a guide to drying various loads.
■ Drying temperature and dryness level are preset when
you choose an Auto Dry Cycle. You can select a different
dryness level, depending on your load, by pressing
Dryness Level and choosing More. Normal or Less.
NOTE: You cannot use the Time Adjust and you cannot
choose a Temperature with the Auto Dry Cycles.
■ If you wish to adjust the cycle length of a Timed Cycle,
press the Time Adjust (More Time or Less Time) arrows.
Adjust the temperature of a Timed Cycle by pressing
Temperature until the desired temperature is selected.
NOTE: You cannot choose a dryness level with Timed
Cycles.
19