beautypg.com

Tij' ■ ■ ■ ■ . . ■ . ■ ■■ 5rrack – Kenmore HE2 110.9758 User Manual

Page 20

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

background image

. ■. ■ ■-■IS

You can customize your cycles by selecting options.

o

tPRE55&HC_.

Wrinkle Guard 90

Cycle Signal

UPRE55SHC_. ..

LOCK/UNLOCK CONTROLS

WRINKLE GUARD® 90

WRINKLE GUARD® 90 helps smooth out wrinkles that form when
you cannot unload the dryer promptly at the end of a cycle.

During this option, the dryer periodically starts and stops,

tumbling the load for 90 minutes.

Press WRINKLE GUARD® 90 to get up to 90 minutes of heat-

free, periodic tumbling at the end of a cycle.

■ Stop WRINKLE GUARD® 90 at any time by pressing

WRINKLE GUARD® 90 or opening the dryer door.

■ WRINKLE GUARD® 90 is preset to OFF. The Auto Dry cycles

will retain the WRINKLE GUARD® 90 setting. For example, If
you select WRINKLE GUARD® 90 in the Normai cycle,
WRINKLE GUARD® 90 will be on the next time you select the
Normal cycle.

NOTE: WRINKLE GUARD® 90 must be selected with a cycle in
order to work. If you do not select WRINKLE GUARD® 90, the
dryer stops after cool down.

Cycle Signal

The Cycle Signal produces an audible sound when the drying

cycle is finished. Prompfly removing clothes at the end of the
cycle reduces wrinkling.

Press CYCLE SIGNAL to turn the signal off.

NOTE: When WRINKLE GUARD® 90 is selected and the Cycle
Signal is on, a tone sounds every 5 minutes until the clothes are
removed, or WRINKLE GUARD® 90 ends.

You can change Auto Cycles, Timed Cycles, Modifiers and

Options anytime before pressing Start.

■ Three short tones sound if an unavailable combination is

selected. The last selection will not be accepted.

Changing Cycles after pressing Start

1. Press STOP twice. This ends the current cycle.

2. Select the desired cycle and options.

3. Press and hold START, The dryer starts at the beginning of

the new cycle.

NOTE: If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically shuts off.

Changing Modifiers and Options after pressing Start

You can change a Modifier or Option anytime before the selected

Modifier or Option begins.

1. Press STOP once.

2. Select the new Modifier and/or Option.

3. Press and hold START to continue the cycle.

NOTE: If you happen to press Stop twice, the program clears and

your dryer shuts down. Restart the selection process.

TIJ'

■ ■ ■ ■ . . ■ . ■ ■■ 5rRack

The dryer rack is shipped in place in your dryer. Remove and
discard any packing material before use.

Use the TUMBLE FREE™ Non-Heated Dryer Rack for items that

you do not want to tumble dry, such as sweaters.

To use the dryer rack

Do not remove the lint screen.

1. Open dryer door.

A. Front edge

2. Place dryer rack inside dryer drum, positioning the back wire

on the ledge of the inner dryer back panel. Push down on
front edge of dryer rack to secure over the lint screen.

A. Dryer rack front edge

B. Dryer back panel

3. Put the wet Items on top of the rack. Leave space between

the items so air can reach all the surfaces.

NOTE: Do not allow items to hang over the edge of the rack.

4. Close the door.

5. Press the POWER button.

6

.

Select a timed cycle and temperature (see following chart).

Items containing foam, rubber, or plastic must be dried on a
clothesline or by using the Air Only temperature setting.

7. You may change the cycle time by pressing MORE TIME or

LESS TIME. Reset time as needed to complete drying. Refer

to the following table.

8

.

Press (and hold) START button (about 3 seconds).

NOTE: You must remove rack for normal tumbling. Do not use
automatic cycles with the dryer rack.

20

This manual is related to the following products: