Kenmore ELITE OASIS Steam 110.6808 - Manual (Page 20)

■ Select the desired Options.
To make changes during an Auto Dry Cycle:
■ Press STOP.
■ Adjust Dryness Level.
NOTE: Dryness Level selections can be made only while
using Auto Dry Cycles.
o
Dryness
Level
Auto Dry Cycles take the guesswork out of drying time
and enhance fabric care. The amount of time that is
displayed is the estimated time remaining in the cycle.
To use a Timed Cycle
■ Select a Timed Cycle.
■ Press the TIME ADJUST (More Time or Less Time)
buttons until the desired drying time is displayed. Press
MORE TIME or LESS TIME once and the time will change
by 1 -minute intervals. Press and hold MORE TIME or
LESS TIME and the time will change by 5-minute
intervals.
NOTE: The Timed Cycle Adjust features can be used only
with Timed Cycles and the Touch Up cycle.
Time Adjust
■ Press TEMPERATURE until the desired temperature
illuminates.
NOTE: During a Timed Cycle, you can change the settings for
Time, Temperature, WRINKLE GUARD® and Cycle Signal.
NOTE: The Temp feature can be used only with Timed
Cycles and the Touch Up cycle.
(OPTIONAL STEP) If desired, select OPTIONS. For more
details, see “Options.”
(OPTIONAL STEP) If desired, press CYCLE SIGNAL. A signal
will sound to alert you when a cycle ends. For more details,
see “Cycle Signal.”
Press START. Be sure the door is closed.
■ If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically shuts off.
■ If you wish to end your drying cycle after pressing Start,
press STOP twice.
To use a SteamCare Cycle
■ Press POWER.
■ Turn the knob to desired SteamCare Cycle.
■ Press the TIME ADJUST up or down arrows until the
desired drying time is displayed. Press the up or down
arrows and the time will change by 1 -minute intervals.
Press and hold the up or down arrows and the time will
change by 5-minute intervals.
NOTE: The Timed Cycle Adjust features can be used only
with Timed Cycles and the Touch Up cycle.
vUlUE r*,
Time Adjust
Press TEMP until the desired temperature illuminates.
• high
• MEDIUM
• LOW
• EXTRA LOW
• a | r fluff
6
TEMP
ADJUST TIMED cvars
NOTE: The Temp feature can be used only with Timed
Cycles and the Touch Up cycle.
NOTE: During the Touch Up cycle, you can change the
settings for Timed Cycle Adjust and Temp Adjust. Open the
door or press PAUSE/CANCEL once to pause the cycle, or
press PAUSE/CANCEL twice to cancel a cycle.
To stop or pause your dryer at any time
Open the door or press STOP once. Press STOP twice to cancel
a cycle.
To restart the dryer
Close the door. Press START until dryer starts.
NOTE: Drying will continue from where the cycle was interrupted
if you close the door and press Start within 5 minutes. If the cycle
is interrupted for more than 5 minutes, the dryer will shut off.
Select new cycle settings before restarting the dryer.
Select the correct cycle and dryness level or temperature for your
load. If an Auto Dry Cycle is running, the display shows the
estimated cycle time when your dryer is automatically sensing
the dryness level of your load. If a Timed Cycle is running, the
display shows the exact number of minutes remaining in the
cycle.
Cool Down tumbles the load without heat during the last few
minutes of all cycles. Cool Down makes the loads easier to
handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Drying tips
■ Follow care label directions when they are available.
■ If desired, add a fabric softener sheet. Follow package
instructions.
■ To reduce wrinkling, remove the load from the dryer as soon
as tumbling stops. This is especially important for permanent
press, knits and synthetic fabrics.
■ Avoid drying heavy work clothes together with lighter fabrics.
This could cause overdrying of lighter fabrics and lead to
increased shrinkage or wrinkling.
Cycle tips
■ Dry most loads using the preset cycle settings.
■ Refer to the Auto or Timed Preset Cycle Settings charts (in
the “Cycles” section) for a guide to drying various loads.
20