Kenmore 8526119A - Manual (Page 16)

Washer continues to fill or drain, or the cycle seems
stuck
Does the drain hose fit too tightly in the standpipe, or is it
taped to the standpipe?
The drain hose should be loose yet fit securely. Do not seal
the drain hose with tape. The hose needs an air gap. (See
“Installation Instructions.")
Washer makes noise
Is the load balanced and the washer level?
The wash load should be balanced. See “Starting Your
Washer” for maximum load size.
The washer must be level. The front feet should be properly
Installed and the nuts tightened. Reset the rear leveling legs if
needed. (See “Installation Instructions.")
Are the self-adjusting rear feet installed?
Can you hear water spraying? This is part of the wash action.
If water is drained quickly from the washer, you may hear air
being pulled through the pump. This happens during the end
of draining. It is normal.
When the cycle changes from washing to draining or
spinning, you may hear a noise as the drive system shifts.
This is normal.
Are you washing items with metal snaps, buckles or
zippers?
You may hear metal Items touching the basket. This is normal.
Are you washing a small load?
You will hear more splashing sounds when washing small
loads. This is normal.
Is the washer installed on a solid floor?
Refer to the “Installation Instructions” for flooring
requirements.
Washer leaks
Check the following:
Are the fill hoses tight? Are the fill hose washers properly
seated? Is the drain hose clamp properly Installed? (See
“Installation Instructions.")
Is the sink or drain clogged?
Sink, floor drain and standpipe must be able to handle 17 gal.
(64 L) of water per minute.
Is water bouncing off the tub ring or the load?
The wash load should be balanced and not overloaded. If
not, the fill or spray rinses can bounce off the load.
The washer must be level. The front and rear feet should be
properly installed and the nuts tightened. Reset the self­
adjusting rear feet if needed. (See “Installation Instructions.”)
Did you pull the drain hose from the washer cabinet and
install it in a standpipe or laundry tub?
(See “Installation Instructions.”)
Check household plumbing for leaks.
Washer basket is crooked
Is the load balanced and the washer level?
The wash load should be balanced.
The washer must be level. The front feet should be properly
installed and the nuts tightened. Reset the rear leveling legs,
if needed. (See “Installation Instructions.”)
Dispensers clogged or leaking
m Are the laundry products in the correct dispenser?
Add the correct amounts of chlorine bleach or fabric softener
to the correct dispenser. Use only liquid chlorine bleach in the
bleach dispenser.
Load too wet
■ Did you use the right cycle for the load being washed?
Select a control setting with a higher spin speed.
■ Did you use a cold rinse?
Cold rinses leave loads wetter than warm rinses. This is normal.
Residue or lint on load
Did you add detergent to the dispenser?
For best results, use the dispenser to dissolve the detergent.
Did you sort properly?
Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also sort by color.
Did you overload the washer?
The wash load must be balanced. See “Starting Your Washer"
for maximum load size. Lint can be trapped in the load if
overloaded. Wash smaller loads.
Was paper or tissue left in pockets?
Did you use enough detergent?
Follow manufacturer’s directions. Use enough detergent to
hold the lint in the water.
Is your water colder than 70°F (21°C)?
Wash water colder than ZO^F (21 °C) may not completely
dissolve the detergent.
Are you using a gentle wash cycle?
Consider using liquid detergent for slow speed cycles such
as Handwash, Casual or Delicate.
16