Kenmore HE3 110 - Manual (Page 13)

Bleach compartment
(Number 4 in Dispenser Illustration)
Add NO MORE THAN Vs cup (80 mL) liquid chlorine bleach to this
compartment. The bleach will be automatically diluted and
dispensed at the best time during the first rinse after the wash
cycle. This compartment cannot dilute powdered bleach.
■ Always measure liquid chlorine bleach. Use a measuring cup
with a pour spout; do not guess.
■ Do not fill beyond the “MAX” level. Overfilling could cause
severe garment damage.
Fabric Softener compartment
(Number 5 in Dispenser Illustration)
Add 1/4 cup (60 mL) liquid fabric softener to this compartment.
Fabric softener will be automatically dispensed in the final rinse.
■ Do not fill beyond the “MAX” level.
■ ri%startirig
1. To pause the washer at any time, select PAUSE/CANCEL.
2. To continue the cycle, select and hold START (for
approximately 1 second).
Changing ^''•'Cioris and
Not all Options and Modifiers are available with all Cycles.
Cycles, Options and Modifiers can be changed anytime before
START is selected.
Options and Modifiers can be changed anytime after START is
selected and before the start of the selected Option or Modifier.
To cancel a cycle and select a new cycle
1. Select PAUSE/CANCEL twice.
2. Select desired cycle.
3. Select the desired OPTIONS.
4. Select and hold START (for approximately 1 second) to restart
the washer at the beginning of the new cycle.
To cancel a cycle
1. Select PAUSE/CANCEL twice.
2. The washer powers down, the door unlocks, and clothes can
be removed.
NOTE: If the water level or the temperature is too high, the
washer will drain automatically before the door unlocks.
To change Options and Modifiers after the cycle has started
1. Select PAUSE/CANCEL.
2. Select the desired OPTIONS or MODIFIERS.
3. Select and hold START (for approximately 1 second) to
continue the cycle.
To drain the washer manually
1. Select PAUSE/CANCEL.
Select DRAIN/SPIN.
Status Ughts
These lights show which portion of the cycle the washer is
operating. They also indicate when you can add an additional
item to the wash cycle and when the controls are locked.
STATUS
A dd A G arment *
P rewash •
W ash •
RINSE •
S pin •
C lothes C lean •
C ontrol L ocked •
Adding items
You can add items to the washer after the cycle has started
Normal/Casual, Heavy Duty or Whitest Whites if the ADD A
GARMENT status light is glowing.
To add items
1. Select PAUSE/CANCEL. The washer door unlocks, and items
can be added.
2. To continue the cycle, close the door and select and hold
START (for approximately 1 second).
Clothes Clean
The Clothes Clean light stays on for 5 minutes after the cycle is
complete. The washer will then power down.
Locking controls
The Control Lock prevents unintended use of the washer. You
can also use the control lock feature to prevent unintended cycle
or option changes during a cycle. When CONTROL LOCKED is
lit, all buttons are disabled except for Pause/Cancel and Start.
You can lock the controls while the washer is operating.
To lock the controls
Select and hold DRAIN/SPIN for 3 seconds.
2 .
3.
4.
Select and hold START (for approximately 1 second) to begin
the drain.
When the spin is complete, the door unlocks. Items can be
removed from the washer.
DRAIN / SPIN
PRESS & HOLD 3
SECONDS TO LOCK/
UNLOCK CONTROL
The CONTROL LOCKED status light glows.
To unlock the controls
Select and hold DRAIN/SPIN tor 3 seconds until the CONTROL
LOCKED Status light turns off.
Estimated Time Remaining
The cycle times vary automatically based on your water pressure,
water temperature, detergent, and clothes load. The cycle time
will be extended if oversudsing occurs or the load is unbalanced.
13