Blinds Chalet Good Housekeeping 3 Room Darkening Sheer Shades - Manual

Please take a moment to identify which headrail version you have and
then follow the appropriate instructions.
A few simple tools are required:
- Measuring tape
- Carpenters Level
- Power drill or Phillips head Screwdriver
- ¼” Hex head and/or Phillips driver bit
Additional fasteners other than those sent with your shading may be
required depending on the mounting surface. Wallboard and plaster
require the use of anchors such as expansion or toggle bolts. Brick,
tile or stone need special plugs and drill bits. Remember to always
pre-drill holes in wood to avoid splitting.
Getting Started
Step 1: Bracket Installation
If the headrail does not sit level, the fabric
will not roll up evenly which could damage
the edges of the shading fabric. Use shims if
necessary to level brackets.
Step 2: Hanging the Shade
No-Headrail
Once the brackets are secured and level, the fabric roll can be inserted.
Make sure your hands are clean to avoid soiling the fabric.
While facing the inside of the shade, be
sure the clutch and roller end plug are in-
serted into the roller. Hold the shade with
the bottom of the clutch facing the floor,
and the beaded cord hanging straight down.
Insert the foot of the control-side
bracket into the slotted center hole of
the clutch. Set nub of the end plug
into the V of the support bracket.
Rotate the T-hook on the support bracket to engage over the nub on
the idler and secure the fabric roll.
Nub
Support Bracket
Fig.15
Low light gap wedges can be used to reduce
the top light gap when the shade is mounted
fully recessed. The wedge is placed between
the mounting surface and the bracket with
the tabs on the wedge facing down and the
thick end of the wedge toward the back of the
bracket.
Optional Extension Brackets are used to project the back of the shad-
ing up to 2 1/2” from the mounting surface. Attach the Ultra Sleek or
Deluxe Mounting Bracket to the Extension Bracket with the nut and
bolt provided.
Measure from window sill up to desired mounting position on each
side of the window frame. Mark position. Mount Side Mount Brack-
ets on each side of window frame as shown. Make sure to confirm
that headrail will sit perfectly level. Once Side Mount Brackets are
installed and properly positioned, attach the Ultra Sleek or Deluxe
Mounting Brackets using the nuts and bolts provided.
To remove the shading, partially lower the shading and insert a flat
head screwdriver as shown. Twist the screwdriver until the headrail
disengages from the bracket.
UltraSleek and
UltraSleek Plus
Mounting Bracket
Deluxe Mounting
Bracket
Wedge for Deluxe
Headrail Bracket
1 1/4” Hex Head
Bracket Screw
Roller Mounting
Brackets for NO
Headrail
Headrail Extension
and Sidemount
Bracket
Nut & Bolt Hold Down Bracket
(optional)
INSIDE MOUNT
Shade Width # of Brackets
Up to 40”
2
>40” - 72” 3
>72”- 84” 4
>84” - 114” 5
No-Headrail
1 1/2” minimum
End Plug Side
Bracket
Control Side
Bracket
T-Hook
Foot
3/4” Minimum for shallow
mount
Minimum for flush inside mount
UltraSleek 3”
UltraSleek Plus 3 3/4”
Deluxe 3 3/4”
UltraSleek & UltraSleek Plus Deluxe
Use shims if necessary to ensure that the headrail is mounted level.
FULLY RECESSED INSIDE MOUNT (Deluxe Bracket Only)
OUTSIDE MOUNT
EXTENSION BRACKETS (optional for headrail shades)
SIDE MOUNT (optional for headrail shades)
No-Headrail UltraSleek & UltraSleek Plus Deluxe
1 1/2” minimum surface 3/4” minimum surface 3/4” minimum surface
UltraSleek & UltraSleek Plus Deluxe
2 1/2” 2 1/2”
2” minimum surface required
UltraSleek & UltraSleek Plus Deluxe
Position screw in center of
slot so you can adjust position
of bracket as necessary.
UltraSleek & UltraSleek Plus
Deluxe Rail
UltraSleek & UltraSleek Plus Deluxe
Push the rail back until it
is fully engaged
Push the rail back until it
is fully engaged
Headrail removal