Crestron electronic TPS-TPI - Manual (Page 9)

Crestron Isys™ TPS-TPI Touchpanel Interface
Leading Specifications
The table below provides a summary of leading specifications for the TPS-TPI
touchpanel interface. Dimensions and weight are rounded to the nearest hundredth
unit.
Leading Specifications for the TPS-TPI Touchpanel Interface
SPECIFICATION DETAILS
Power Requirements (without cards) 10.0 Watts (0.417 Amp @ 24 VDC) 1
SIMPL TM Windows ® Version 1.50.05 or later 2
CNMSX-AV/PRO Upgrade File (.upz) Version 51125X or later 3 & 4
CNRACKX/-DP Upgrade File (.upz) Version 51125W or later 3 & 4
CEN/CN-TVAV Upgrade File (.upz) Version 51130V or later 3 & 5
CNMS, CNRACK, CNLCOMP Version 3.18.09m, l, c or later 3 & 5
Operating System
ST-CP Operating System
Version 4.00.49 or later 3 & 5
ST-CP Monitor Version 1.29 or later 3
VisionTools TM Pro-e (VT Pro-e) Version 2.2.0.0 or later 2
Crestron Database Version 14.1 or later 2
Memory 8MB of flash; 8MB of DRAM 6
Speaker Amplification 2 Watts per channel
Dimensions & Weight Height: 9.45 in (24.00 cm)
- with ears Width: 15.20 in (38.61 cm)
Depth: 2.92 in (7.42 cm)
Weight: 3.90 lb (1.77 kg)
1 The individual power requirements for the expansion cards are:
TPS-ENETL: 4Watts (0.167 Amps @ 24 VDC)
TPS-VIDL: 8 Watts (0.333 Amps @ 24 VDC)
TPS-XVGAL: 10 Watts (0.417 Amps @ 24 VDC)
2 The latest software versions can be obtained from the Downloads page (SIMPLWIN, TOUCHPNL,
VTPRO-E, or CRESDB Libraries) of the Crestron website (
www.crestron.com) .
3 CNX upgrade files are required for either CNMSX-AV/Pro or CNRACKX/-DP. Filenames for CNX
upgrade files have a UPZ extension and SmarTouch files are in one EXE. All can be obtained from
the Downloads page (OPSYS Library) of the Crestron website.
4 When loading VT Pro-e files or firmware through the RS-232 port of the control system, be sure that
the baud rate is at 57600 or lower. Otherwise, the Viewport may post the "Transfer Failed" message.
5 These control systems do not support loading of firmware or VT Pro-e files to the TPS-TPI through
the RS-232 port of the control system. In order to load these files to the TPS-TPI when using these
control systems, either use the RS-232 port on the TPS-TPI or use Ethernet direct to the unit
(assuming the TPS-ENETL is installed).
6 Additional memory can be purchased, refer to " Memory " on page 2. The complexity of the control
screens and the sampling of the WAV files influence memory usage.
As of the date of manufacture, the TPS-TPI has been tested and found to comply
with specifications for CE marking.
NOTE: This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Operations Guide - DOC. 5855 Touchpanel Interface: Crestron Isys™ TPS-TPI • 5