Preparations, Manual tuning procedure, Direct tuning procedure – Panasonic NV-SJ200 User Manual
Page 10: Fine tuning procedure, Blanking of unused programme positions
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Preparations
• Confirm that the TV is on and the VCR viewing channel is
selected.
• Turn on the VCR and select any programme position
except AV.
• Set the VCR/TV switch © is set to “VCR".
Manual Tuning Procedure
1 Press the MENU button © to display the Main menu on
the TV screen.
2 Press the Cursor buttons
(AT)
© to select TUNER
PRESET then press the ENTER button
3 Press the Cursor buttons ( A T ) © to select “CH” then
select the channel number you want to tune by pressing
the Cursor buttons (◄ ►) ©.
4 Confirm that “CLEAR” is set to “OFP.
5 Press the Cursor buttons ( A T ) ^ to select “SEARCH"
then press the Cursor buttons (-^ ►) © to start the
Manual Tuning.
On Screen Display
6 If the desired TV station has not been tuned, press the
Cursor buttons (*^ ►) © again.
• Press the MENU button © and repeat steps 3-5 for
each programme position you want to tune to a station.
7 Press the MENU button © three times to exit the On
Screen Display.
Direct Tuning Procedure
1 Press the MENU button © to display the Main menu on
the TV screen,
2 Press the Cursor buttons
(AT)
© to select TUNER
PRESET then press the ENTER button ©.
3 Press the Cursor buttons
(AT)
© to select “CH" then
select the channel number you want to tune by pressing
the Cursor buttons (◄ ►) ©.
Fine Tuning Procedure
1 Press the MENU button © to display the Main menu on
the TV screen.
2 Press the Cursor buttons
(AT)
© to select TUNER
PRESET then press the ENTER button ©.
3 Press the Cursor buttons
(AT)
© to select “CH” then
select the channel number you want to tune by pressing
the Cursor buttons (◄ ►) ©.
4 Press the Cursor buttons ( A T ) © to select “FINE" then
press the Cursor buttons (◄ ►) © to start the Fine
Tuning.
• Press the ENTER button © to return the tuning to its
former state.
5 Press the MENU button © to exit the On Screen Display.
Blanking of Unused Programme Positions
1 Press the MENU button © to display the Main menu on
the TV screen.
2 Press the Cursor buttons
(AT)
© to select TUNER
PRESET then press the ENTER button ©.
3 Press the Cursor buttons (A T) © to select "CH" then
select the channel number you want to tune by pressing
the Cursor buttons (◄ ►) ©.
4 Press the Cursor buttons ( A T ) © to select “CLEAR"
then press the Cursor buttons (◄ ►) © to select “ON”.
* Repeat steps 3-4 for other unused programme
positions to skip during the selection of programme
positions.
• To cancel the blanking of a programme position select
that programme position then select “CLEAR” is “OFP.
5 Press the MENU button © twice to exit the On Screen
Display.
4 Confirm that “CLEAR" is set to “OFP.
5 Press the Cursor buttons
(AT)
© to select “SEARCH".
6 Press the Numeric buttons o to enter the number of the
desired programme position.
For the 5A and 9A channels, input the following numbers:
90 for CH-5A, 91 for CH-9A. (Example for Australia.)
• For other channels that require tuning, repeat
steps 3-6.
7 Press the MENU button © twice to exit the On Screen
Display.