Manual tuning procedure, Direct tuning, Fine tuning procedure – Panasonic NV-SD230A User Manual
Page 13: Blanking of unused programme positions, Ch add&delete
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Manual Tuning Procedure
Press
MENU.
Select
TUNER PRESET by pressing A or V and
ENTER.
Select
CH by pressing A or ▼ then select the channel
number you want tuned by pressing ◄ or ►.
Confirm that
CLEAR is set to OFF.
Select
SEARCH by pressing
A
or ▼ then press ◄ or
SEARCH 74
EHD:MENU
6
If the desired TV station has not been tuned, press ◄ or
► again.
• Press
MENU and repeat steps 3-5 for each
programme position you want to tune to a station.
• To exit, press
MENU three times.
Direct Tuning
1 Repeat steps 1-4 in ManualTuning.
2 Select SEARCH by pressing
A
or ▼.
3
Using the
numeric buttons on the remote controller
(Ensure that
VCR/TV switch is set to VCR.), enter the
same number as the number of the channel to be tuned.
For the 5A and 9A channels, input the following
numbers: 90forCH-5A, 91 forCH-9A.
• For other channels that require tuning, repeat steps
3-
4 in ManualTuning and steps 2-3 above.
• To exit, press
MENU twice.
Fine Tuning Procedure
1 Press MENU.
2 Select TUNER PRESET by pressing
A
or ▼ and
ENTER.
3
Select
CH by pressing
A
or ▼ then select the
programme position by pressing ◄ or ►.
4 Select FINE by pressing
A
or
T.
5 Press ◄ or ► to obtain the best tuning condition.
•
• To return the tuning to its former state, press
ENTER.
Press
MENU.
Blanking of Unused Programme Positions
1
Press
MENU.
2
Select
TUNER PRESET by pressing
A
or ▼ and
ENTER.
3
Select
CH by pressing
A
or ▼ then select the
programme position by pressing ◄ or ►.
4 Select CLEAR by pressing
A
or ▼.
5
Select
ON by pressing ◄ or ►.
• Repeat steps 3-5 for other unused programme
positions to skip during the selection of programme
positions.
• To cancel the blanking of a programme position, select
that programme position then select
CLEAR OFF.
6 Press MENU twice.
CH ADD&DELETE
Press
MENU.
Select
CH ADD&DELETE by
pressing
A
or
T
and
ENTER.
Select
CH by pressing
A
or ▼
then select
ADD or DELETE by
pressing ► or
Before Adding
After Adding
POS CH
POS CH
1 2
1 2
2 4
2 4
3 6
3
4 8
4 6-
5 10
5 8
6 12
6 10
7
7 12-
8
8
Added CH
SHIFT
Before Deleting
After Deleting
POS CH
POS CH
1 2
1 2
2
4
3
6^
' Deleted CH
2
4
3
8-
4 8
4 10
5 10
5 12-
6 12
6
7
7
8
a
SHIFT f
• Adding
CH shifts the programme positions up, and deleting
CH shifts them down, as shown in the table above.
• After adding, Tune the added
CH. (See steps 3-5 in
ManualTuning.)
• Press
MENU (for adding only) and repeat step 3 for
each of the other programme positions.
4
Press
MENU several times.
13