Yamaha Disklavier PRO Series - Manual (Page 10)

If you want to transpose the MIDI output, press the [i^ ] cursor button to
position the in cursor next to the Trans parameter, then use the Dial or
the [-/NO] and [+/YES] buttons to set a value.
-10 -8 -6 -4 -2 O O O O O O O O O O-'
-r->spiit.[;c4 ]
Tr-Hiins Lli" 00 R - I¿ifi
-/NO +A'ES
The MIDI output can be transposed from -60 to +60 in one semitone steps.
Seperate transposition values can be set for the left- and right-hand parts.
Press the [^ ] cursor button.
4i »
The following display appears.
1 ouc-f’!
Ped:al:=ni:::i;:iHT
Use the Dial or the [-/NO] and [+/YES] buttons to set the options.
-10 -8 -6 -4 -2 9
o o o o o o o o o
-VNO -t-ZYES
Parameter Option Description
Key Touch
ON (default) Sends silent notes, diminishing sounds in Silent
mode
OFF Doesn’t send key touch data.
Pedal
CONT (default) Sends continuout pedal data.
SWITCH Sends ON/OFF pedal data.
Press the [◄i ] cursor button until the following display appears.
+0UÍ C:!-i-01 02 (L :• h!
Prg:==###.tt ## Unl:=: №##!■ ###
If you did not set a split point, the subsequent displays will be similar to the following.
i;-i ii .it. i:h “01 “I-
Pr-g::.:### Uol If ## it
12 Chapter 3: Enhanced Mode and XP Mode
Press the [^i ] cursor button to position the ii> cursor next to the Out Ch
parameter, then use the Dial or the [-/NO] and [+/YES] buttons to set a
value.
-10 -8 -6 -4 -2 9
O O O O O O O O O o-a'-
-/N0 +/YES
The “Out Ch” option is used to select the MIDI channel/s on which the Disklavier will
transmit MIDI data.
It can be set to OFF, MIDI channels 1 to 16 or HP.
Channel Description
OFF No data is sent to the MIDI instrument.
1 to 16 The Disklavier keyboard data and pedal data is sent on the selected
channel.
HP Keyboard data and on/off pedal data will be sent on channel 1, and
continuous pedal data (half pedal) will be sent on channel 3. In this case the
pedal data will be continuously variable (half pedal).
m
3
'S.
55’
□r
To select a voice for the MIDI output, press the [^ ] cursor button to
position the !i> cursor next to the Prg parameter, then use the Dial or the
[-/NO] and [+/YES] buttons to select a voice.
^ ^ -10 -8 -6 -4 -2 9
1 1 1 o o o o o o o o o O-^c
-/NO +/YES 1 1 1
-•i-Out- Ch ==01.02 '(L.p;:- -i-
Pr-glf-## #:.### Uol :=::###,###
If you had set a split point, you can set different voices for the left- and right-hand parts.
A setting of “###” means no voice selection.
To set the volume of the MIDI output, press the [i^ ] cursor button to
position the ii^ cursor next to the Vol parameter, then use the Dial or the
[-/NO] and [+/YES] buttons to set the volume.
-10 -8 -6 -4 -2
O O O O O O O O O o-
=01.02 (.LvR‘>
P|.-.g:=:##: t.### Uol If###.###
-/NO +/YES
If you had set a split point, you can set different volume levels for the left- and right-hand
piano parts.
A setting of “###” will not change the volume.
Filtering KBD Out Data in Enhanced Mode
13