OFNA Racing LD3 Pro - Manual (Page 6)

Parts Upgrade
Parts Upgrade
38477 - Manifold
In-Line Rear Exhaust Manifold
Polished
38476 - Pipe
In-Line Rear Exhaust Manifold
Polished
97501
Manifold Spring
10121
Manifold Spring
PRO ASSEMBLY OF THE MANIFOLD AND MUFFLER
38475 - Polished
IN-LINE REAR EXHAUST PIPE
10063 - polished 6 Ring Pipe
38286 - Side Exht Manifold
* Place the clutch shoes
with the clutch springs
over the 3 pins of the
flywheel.
Using a small screw driver
or needle nose pliers and push
the small end of the clutch
spring behind the pilot shaft
nut and down.
If installed correctly, the shoes
will be held in with spring
tension.
3 Shoes Flywheel
(Small/30mm)
3 Shoes Flywheel 34mm, Pull Start
- 3 Shoes Flywheel, non-pull Start
(Small/30mm)
Clutch Shoes
Clutch Spring
38285
38284 -
38285
10100
10010
10098
SG
Clutch Nut
10330
Split Cone
* Put the clutch spring into the groove
of the clutch shoesbefore assembly.
94005
M3x15mm
Screw
M3x15mm
Screw
94033
M3x3mm
Set Screw
94033
M3x3mm
Set Screw
Step2
Step3
Step1
38418
Stabilizers
Mount
38418rs
Mount
38418
Stabilizers
Balance
Adjuster
38420
Stabilizers
blades
38419
3x55mm
Lower Arm
Shaft
Parts Upgrade
38319 - CHASSIS 2.5mm
38489 - CHASSIS 3.0 mm Ld3 Pro
94033
M3x3mm
Set Screw
PRO ASSEMBLY OF THE STABILIZER INTO ARM BLOCK 38417 - Blade Swaybar Set
* Keep stabilizer ball in the center. * Turn stabilizer balance adjuster to
adjust the stabilizer to the same angle.
* Assembly the rear anti-roll bar same as the front.
SG Type Engine
ASSEMBLY OF THE FLYWHEEL
Center
Pull Start Engine Mounts
#38150
Non-Pull Start Engine Mounts
#38453
Parts Upgrade
Step 1
Step 3 Step 3
Step 2
Step 4
10mm Alum.
Set Screw
5x11x4mm
Ball Bearing
Rear Lower Arm
10x15x4mm
Ball Bearing
6mm
Ball&Socket
CVA Joint
CVA Joint
Rear Wheel
Hub
8mm
Steering Ball
8mm
Steering Ball
Washer
39150
37430
38399
38261
Rear Upper shaft
38270
Shock Tower
94004
M3x12mm
Screw
38266
37450
37370
38405
38405
39140
38266
*Notice the direction
of the steering ball washer.
94019
M3x10mm
Flat Head
Hex Screw
90020
2.5mm
E-Ring
90020
2.5mm
E-Ring
Lower Arm Shaft
Arm Holder
(Rear / Rear)
38419
38263
* Use the 0 degree
for rear arm holder.
Parts Upgrade
Parts Upgrade
PRO ASSEMBLY OF THE REAR HUB 38268 - Rear Drive Shaft
Assembly of the right and left-side are the same.
Assembly of the right and left-side are the same.
PRO ASSEMBLY OF THE REAR SUSPENSION ARMS
38399 Rear Upper Arm
Ball End
38399 Rear Upper Arm
Ball End
38398
3x20mm
Turnbuckle
Rear Upper Arms
38399 - Rear Upper Arms
Rear Lower Arms
38399 - Rear Lower Arms
* Use a 3mm drill to drill
a hole in the arm holder
before assembly.
For assembly front roll bar:
Insert the upper arm shaft after assembly the shock tower.