Rane DC 22 (2003 version) - Manual (Page 5)

Manual-
Rear Panel Description
INPUTS 1 and 2: Choose between the balanced XLR or the balanced/unbalanced ¼" TRS jacks, but only use one. Inserting a ¼"
TS jack will work—however—we recommend using balanced lines, especially when connecting any cable over 10 feet (3 meters)
in length. Consult the Sound System Interconnection RaneNote provided with this manual.
INPUTS 1 and 2 Gain Trim Switch: In its +4 dBu position, the Input gain of the respective channel is unity. In the -10 dBV posi-
tion, the input gain is increased by 12 dB (although mathematically suspicious, it really is 12 dB, not 14 dB) to compensate for
certain recording devices. This switch must be in the +4 dBu position for front panel calibration accuracy.
OUTPUTS 1 and 2 are delivered by the balanced XLR or the unbalanced ¼" TS jacks. Using both types of Outputs are permissible
to drive two devices, such as an amplifier and a recorder. This device uses low impedance balanced line drivers. Do not connect the
XLR “+” or “–” output pins to ground, as this may cause the power supply to shut down. For unbalanced use, leave the unused output pin
(“+” or “–”) unterminated.
System wiring example for a DJ system
+4 dBu
-10 dBV
BALANCED BALANCED UNBAL BAL/UNBAL +4 dBu
-10 dBV
WIRING
3-PIN XLR:
PIN 1 = CHASSIS, SHIELD, PIN 2 = (+), PIN 3 = (–)
¼" PHONE, BALANCED:
TIP = (+), RING = (–), SLEEVE = CHASSIS, SHIELD
¼" PHONE, UNBALANCED:
TIP = SIGNAL, RING = GROUND, SLEEVE = CHASSIS, SHIELD
DC 22
MADE IN U.S.A.
RANE CORP.
INPUT
2
OUTPUT
2
ACN 001
345 482
BALANCED BALANCED UNBAL BAL/UNBAL
INPUT
1
OUTPUT
1
FOR CONTINUED GROUNDING PROTECTION
DO NOT REMOVE SCREW
50/60 Hz
12 WATTS
120 V
MP 22z
RANE CORP.
POWER
750mA
BALANCED 1/4" TIP (+) RING (-)
ACN001.187.837
R
MASTER
L
SLEEVE (GND)
CLASS 2 EQUIPMENT
MADE IN U.S.A.
ZONE 2 ZONE 1
R
L MIC/AUX MIC/AUX
OUTPUTS
ZONE 1
YES NO YES NO
TAPE OUT TO TO
R LINE IN AUX
R R
L
L
L LINE 6
TR IM 6
MASTER LOOP SEND (OUT)
RETURN (IN) TAPE LINE 5
R
L TR IM 5
INPUTS
LINE 4 LINE 3
R
L TR IM 4
LINE (RIAA) PHONO
TR IM 2
TR IM 3
R
PHONO (RIAA) PH/LN 1
L TR IM 1
PH/LN 2
ACTIVE CROSSFADER TECHNOLOGY PATENT PENDING PHONO TIP (SIG) SLEEVE (GND)
RETURN
(IN)
SEND
(OUT)
MIC LOOP
INPUT
MIC/LINE REMOTE
UNBALANCED 1/4"
LINE
GROUND
DC 22 STEREO COMPRESSOR
MP 22z MIXER
SAC 22 STEREO 2-WAY CROSSOVER
SEQ 30S STEREO EQUALIZER
OUTPUTS INPUTS
RIGHT LEFT
OUTPUTS
LEFT
INPUTS
RIGHT
LEFT RIGHT RIGHT LEFT
LEVEL LEVEL 0 10 0 10
LEVEL LEVEL 0 10 0 10
STEREO AMP, HIGH
MONO OR BRIDGED AMP, MONO SUB
RIGHT SPEAKER
LEFT SPEAKER
MONO SUBWOOFER
LEFT RIGHT LEFT RIGHT LEFT RIGHT
SUB
FILTER OUT IN 50/60 Hz 12 WATTS
120 V
HIGH OUTPUTS LOW OUTPUTS
MONO
SUB OUTPUT INPUTS
WIRING PIN 2 = POSITIVE
PIN 3 = NEGATIVE
PIN 1 = CHASSIS GROUND
N108
FOR CONTINUED GROUNDING PROTECTION DO NOT REMOVE SCREW
SAC 22
MADE IN U.S.A. RANE CORP. 100 Hz
+4 dBu -10 dBV N108 BALANCED BALANCED UNBAL BAL/UNBAL +4 dBu -10 dBV
WIRING
3-PIN XLR:
PIN 1 = CHASSIS, SHIELD, PIN 2 = (+), PIN 3 = (–)
¼" PHONE, BALANCED: TIP = (+), RING = (–), SLEEVE = CHASSIS, SHIELD
¼" PHONE, UNBALANCED: TIP = SIGNAL, RING = GROUND, SLEEVE = CHASSIS, SHIELD
DC 22
MADE IN U.S.A. RANE CORP.
INPUT 2 OUTPUT 2
BALANCED BALANCED UNBAL BAL/UNBAL
INPUT 1 OUTPUT 1
FOR CONTINUED GROUNDING PROTECTION DO NOT REMOVE SCREW
50/60 Hz 12 WATTS
120 V
MADE IN U.S.A. RANE CORP.
OUTPUTS SEQ 30S INPUTS
RIGHT RIGHT LEFT LEFT
UNBALANCED BAL / UNBAL UNBALANCED BAL / UNBAL BALANCED BALANCED BALANCED BALANCED
N108
50/60 Hz 12 WATTS
120 V
FOR CONTINUED GROUNDING PROTECTION DO NOT REMOVE SCREW WIRING 3-PIN XLR: PIN 1 = CHASSIS, SHIELD, PIN 2 = (+), PIN 3 = (–). ¼" PHONE, BALANCED: TIP = (+), RING = (–), SLEEVE = CHASSIS, SHIELD. ¼" PHONE, UNBALANCED: TIP = SIGNAL, RING = GROUND, SLEEVE = CHASSIS, SHIELD.