Kontron AM5020 User Manual
User guide, Am5020
Table of contents
Document Outline
- Revision History
- Imprint
- Disclaimer
- Table of Contents
- List of Tables
- 1-1 System Relevant Information 1 - 5
- 1-2 AM5020 Main Specifications 1 - 10
- 1-3 Standards 1 - 15
- 1-4 Related Publications 1 - 16
- 2-1 Features of the Processors Supported on the AM5020 2 - 4
- 2-2 Module Management LED Functions 2 - 8
- 2-3 User-Specific LED Functions 2 - 9
- 2-4 POST Code Sequence 2 - 10
- 2-5 POST Code Example 2 - 10
- 2-6 Module Handle Positions 2 - 11
- 2-7 DIP Switch SW3 Functions 2 - 12
- 2-8 DIP Switch SW4 Functions 2 - 12
- 2-9 USB Connectors J6/J7 Pinout 2 - 13
- 2-10 Serial Connector J4 (COMA) Pinout 2 - 14
- 2-11 DVI-D Connector J9 Pinout 2 - 15
- 2-12 SATA Connector J8 Pinout 2 - 16
- 2-12 Gigabit Ethernet Connectors J1 and J3 Pinout 2 - 18
- 2-13 Pinout of AMC Card-edge Connector J1 2 - 22
- 2-14 Reserved Pins Description 2 - 25
- 2-15 Extended Options Region Single-Ended Pins Description 2 - 25
- 2-16 JTAG Pins Description 2 - 25
- 2-17 Processor and Chipset Supervision 2 - 27
- 2-18 AMC-Specific Signals 2 - 27
- 2-19 Onboard Power Supply Supervision 2 - 27
- 2-20 Temperature Signals 2 - 28
- 4-1 Configuration of DIP Switch SW3, Switches 1 and 2 4 - 4
- 4-2 Configuration of DIP Switch SW3, Switches 3 and 4 4 - 4
- 4-3 DIP Switch SW4 Configuration 4 - 4
- 4-4 I/O Address Map 4 - 5
- 4-5 Status Register 0 (STAT0) 4 - 6
- 4-6 Control Register 0 (CTRL0) 4 - 7
- 4-7 Control Register 1 (CTRL1) 4 - 7
- 4-8 Device Protection Register (DPROT) 4 - 8
- 4-9 Reset Status Register (RSTAT) 4 - 9
- 4-10 Board Interrupt Configuration Register (BICFG) 4 - 10
- 4-11 Board ID High Byte Register (BIDH) 4 - 10
- 4-12 Board and PLD Revision Register (BREV) 4 - 11
- 4-13 Geographic Addressing Register (GEOAD) 4 - 11
- 4-14 Watchdog Timer Control Register (WTIM) 4 - 13
- 4-15 Board ID Low Byte Register (BIDL) 4 - 14
- 4-16 User-Specific LED Configuration Register (LCFG) 4 - 15
- 4-17 User-Specific LED Control Register (LCTRL) 4 - 16
- 4-18 MMC Serial over LAN Configuration Register (ISOL) 4 - 17
- 4-19 MMC Clock E-Keying Configuration Register (ICKEY) 4 - 17
- 4-20 MMC AMC E-Keying Configuration Register 0 (IAKEY0) 4 - 18
- 4-21 MMC AMC E-Keying Configuration Register 1 (IAKEY1) 4 - 19
- 4-22 MMC Controller Status Register 0 (ICSTA0) 4 - 20
- 4-23 MMC Controller Status Register 1 (ICSTA1) 4 - 21
- 4-24 MMC Reset Status Register (IRSTA) 4 - 22
- 5-1 DC Operational Input Voltage Ranges 5 - 3
- 5-2 AM5020 in uEFI Shell Mode 5 - 6
- 5-3 AM5020 with Win. XP in Idle Mode 5 - 6
- 5-4 AM5020 with Win. XP and Max. Processor Work Load (Graphics Idle) 5 - 6
- 5-5 AM5020 with Win. XP and Max. Processor and Graphics Work Load 5 - 6
- 5-6 Payload Power Consumption of AM5020 Accessories 5 - 6
- 5-7 IPMI FRU Payload Power Consumption 5 - 6
- 5-8 Payload Start-Up Current of the AM5020 5 - 7
- 6-1 AM5020 Airflow Impedance by Zone [N/m²] 6 - 9
- 6-2 AM5020 Airflow Impedance by Zone [inches H2O] 6 - 10
- 6-3 Deviation of the Airflow Rate on the AM5020 6 - 11
- A-1 SATA Flash Module Main Specifications A - 3
- List of Figures
- 1-1 AM5020 Functional Block Diagram 1 - 6
- 1-2 AM5020 Front Panel 1 - 7
- 1-3 AM5020 Board Layout (Top View) 1 - 8
- 1-4 AM5020 Board Layout (Bottom View) 1 - 9
- 2-1 Front Panel LEDs 2 - 7
- 2-2 Module Handle Positions 2 - 11
- 2-3 USB Connectors J6/J7 2 - 13
- 2-4 Serial Con. J4 (COMA) 2 - 14
- 2-5 DVI-D Connector J9 2 - 15
- 2-6 SATA Connector J8 2 - 16
- 2-7 Gigabit Ethernet Connectors J1 and J3 2 - 18
- 2-8 AM5020 Port Mapping 2 - 20
- 3-1 Module Handle Positions 3 - 4
- 4-1 DIP Switches SW3 and SW4 4 - 3
- 6-1 AM5020 with i7-610E, 2.53 GHz 6 - 8
- 6-2 AM5020 with i7-620LE, 2.0 GHz 6 - 8
- 6-3 AM5020 Airflow Impedance 6 - 9
- 6-4 Thermal Zones of the AM5020 Module 6 - 10
- A-1 SATA Flash Module Layout (Bottom View) A - 4
- Proprietary Note
- Trademarks
- Environmental Protection Statement
- Explanation of Symbols
- For Your Safety
- Two Year Warranty
- 1. Introduction