BoonDocker POLARIS: Non-turbo Control Box 600 IQ 2 INJ User Manual

Page 17

BoonDocker – 1585 Hollipark Dr. Idaho Falls, ID 83401 – 208-542-4411 / 877-522-7805

www.boondockers.com – email:

[email protected]

– fax: 208-524-7381

Revised 2-13-08

Page 17 of 19

C. N2O Configuration Examples

The following are examples of settings to achieve the various nitrous triggering configurations described in Section A
above:

1. Button only: Activate nitrous only

when the button is pressed.

Fuel TPS RPM Btn
040 OFF OFF

N2O

Set: TPS to OFF, RPM to OFF, and Btn to

N2O.

2. TPS only: Activate nitrous only

when the Throttle is pressed
beyond a set level.

Fuel TPS RPM Btn

040

200 OFF OFF

Set: TPS to ON (set the TPS threshold to the

desired level), RPM to OFF, Btn to OFF.

3. TPS and RPM only: Activate

nitrous only when the Throttle is
pressed beyond a set level AND
when RPMs are with a certain
range.

Fuel TPS RPM Btn
040 200

ON OFF

Set: TPS to ON (set TPS threshold to desired

level), RPM to ON (set Min/Max to
desired levels), Btn to OFF.

4. Button (N2O) or TPS: Activate

nitrous when button is pressed or
when Throttle is pressed beyond a
set level.

Fuel TPS RPM Btn

040 200 OFF

N2O

Set: TPS to ON (set TPS threshold to desired

level), RPM to OFF, and Btn to N2O.

5. Button (N2O) or TPS and RPM:

Activate nitrous when button is
pressed or when Throttle is pressed
beyond a set level AND the RPMs
are within a certain range.

Fuel TPS RPM Btn

040 200 ON

N2O

Set: TPS to ON (set TPS threshold to desired

level), RPM to ON (set Min/Max values),
and Btn to N2O.

6. Button (ARM) and TPS:

Activate nitrous when button input
is on (armed) AND Throttle is
pressed beyond a set level.

Fuel TPS RPM Btn
040 200 OFF

ARM

Set: TPS to ON (set TPS threshold to desired

level), RPM to OFF, and Btn to ARM.

7. Button (ARM) and TPS and

RPM: Activate nitrous when
button input is on (armed) AND
Throttle is pressed beyond a set
level AND the RPMs are within a
certain range.

Fuel TPS RPM Btn

040 200 ON

ARM

Set: TPS to ON (set TPS threshold to desired

level), RPM to ON (set Min/Max values),
and Btn to ARM.

D. N2O Pressure Transducer Faults

If the Nitrous Mode is set to FIX, the pressure transducer is ignored and no Nitrous faults should appear. If the
Nitrous Mode is set to ADJ or NON, when the nitrous button is pressed, the Control Box first checks to make sure
the readings from the pressure transducer are correct. One of the following two fault messages may be displayed. If
a fault message is displayed, the nitrous solenoid will not operate and the message will remain displayed until any key
is pressed to clear it or the engine is restarted.

ERROR: N2O press

too LOW! .

This screen may appear if the pressure in the N2O tank is zero, the transducer is unplugged, or there is a wiring
problem.

Important Note: If the bottle becomes empty, this message will be displayed and nitrous will be shut off to prevent
extra fuel from being added without nitrous!

ERROR: N2O press

over 2000psi .

This screen will appear if the pressure transducer senses a pressure above 1000psi for regulated systems or 2000psi for
non-regulated systems.